Bedienungsanleitung Hitachi NT65GS (Seite 14 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568893

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

English

⅜ Keep away from ignition sources. No smoking.

⅜ Clear the area of children or unauthorized personnel.

⅜ Do not store the tool, fuel cell and battery in a cold

weather environment. Keep the tool, fuel cell and

battery in a warm area until beginning the work.

⅜ If the tool, fuel cell and battery are already cold, bring

it in a warm area and allow the tool to warm up before

use.

Observe temperature limit of max. 50°C (120°F).

Do not expose to an open flame and sparks!

⅜ This tool may not drive completely below when;

– at low temperature fuel cell loose the required

propellant force,

– at high temperature fuel cell overdose.

⅜ Do not use the tool in the rain or where excessive

moisture is present.

⅜ This tool is not recommended for use at altitudes

above 1500 m (5000 feet), or in temperature below

0°C (30°F).

1. Fuel cell

To attach the metering valve to a fuel cell:

(1) Separate the metering valve and the cap from the gas

cartridge (See Fig. 3 (1)).

(2) Press forward (stem side) and downward on the front

side of the metering valve (See Fig. 3 (2)).

(3) Press downward on the rear of the metering valve

until it seals (See Fig. 3 (3)).

Check the metering valve:

Press the metering valve stem on fuel cell two or three

times against a stationary object and release.

If gas is not dispersed, fuel cell is empty. Replace it.

Observe Safety Regulations

CAUTION

⅜ If the gas leaks from the metering valve or the gas

cartridge after attached the metering valve, replace

with the new metering valve.

⅜ Do not attempt to reuse the metering valve.

Replace with the new metering valve.

2. Battery

You must charge the battery before use.

The charging method of battery is shown in page 12.

3. Check on safety

CAUTION

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the top cover,

etc. for tightness.

Check the tool for defective or rusty parts.

⅜ Check whether or not the push lever works correctly

without nails, fuel cell and battery. Also check whether

or not any dirt has adhered to the moving parts of the

push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)

Do not operate the push lever or trigger while

installing the battery.

Make sure the battery indicator light is flashing GREEN

(See Fig. 5).

If the battery indicator light is flashing RED, the battery

doesn’t have enough power and it needs to be

charged.

BATTERY INDICATOR LIGHT

– Flashing GREEN: Enough power remaining (The

light turns steady during

operation).

– Flashing RED: Insufficient power remaining (The

light turns steady during operation).

–OFF: The battery is extremely empty. Charge the

battery.

2. Insert fuel cell into the tool

(1) Push up and pull out the actuater (See Fig. 6).

(2) Insert the fuel cell into the tool (See Fig. 7).

(3) Insert the stem of fuel cell into the hole of adaptor

(See Fig. 8).

(4) Close the actuater (Fig. 9).

3. Load nails

CAUTIONS

⅜ When loading nails into Nailer,

(1) do not depress trigger;

(2) do not depress push lever; and

(3) keep your face, hands feet and other body parts,

as well as those of other persons away from the

nose muzzle to avoid possible injury during usage

and carrying.

(1) Insert nail strip into rear of magazine (See Fig. 10).

(2) Slide the nail strip forward in the magazine (See Fig. 11).

(3) Push the nail feeder (A) to engage the nail feeder (B)

to the nail strip (See Fig. 12).

NOTE

⅜ Use nail strip of more than 10 nails.

The Nailer is now ready to operate.

Removing the nails:

1 Pull the nail feeder (B) backward (See Fig. 13).

2 Return the nail feeder (B) forward quietly while

pushing the nail feeder (A).

3 Pull out nails from the back of the magazine (See Fig.

14).

(1) Lightly press the stop lever and gently pull out the

magazine cover. (See Fig. 15)

(2) Set nail strip into the magazine and keep the points

of nails in contact with groove. (See Fig. 16)

(3) Slide the nail strip into the blade guide. (See Fig. 17)

(4) Confirm that nail strip is placed with side guide

grooves and groove properly, then push the magazine

cover forward to be latched.

NOTE

⅜ The nails shown in page 11 can be loaded onto the

side guide groove of the magazine without any

adjustment.

Always keep the points of nails in contact with Groove.

01Eng_NT65GS_WE 12/3/08, 8:4513

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NT65GS Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info