Bedienungsanleitung Hitachi NT65M2 (Seite 11 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568895

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

English

⅜ Do not point the air outlet of blow nozzle at a person.

⅜ Do not use the blow nozzle with the push lever left fit.

This Nailer has a blow nozzle that blows out wood

shavings which occur during work.

Press the knob with your thumb to use the blow nozzle

(See Fig. 10).

NOTE

⅜ When the blow nozzle is used for a long time, the

nailing force may degrade temporarily. In this case,

allows the air supply pressure to stabilize before

starting work.

⅜ Oil in the body or drained water from the compressor

can sometimes spout out of the air outlet of blow

nozzle. It is recommended that you once conduct a

test before use and see if such phenomenon happens

at an environment where spouted oil will cause any

inconvenience.

4. Changing the exhaust direction

The direction of the exhaust vent can be changed by

turning the top cover (See Fig. 11).

5. Using the nose cap (See Fig. 12)

The nose cap is attached to the push lever tip to

protect the workpiece from scratches or damage.

Remove in the order shown below when not using.

(1) DISCONNECT AIR HOSE FROM NAILER.

(2) Put the nose cap to the tip of the push lever.

⅜ Attach to the tip of the push lever in the reverse order

of detaching.

NOTE

⅜ The nose cap may reduce nailing depth due to its

thickness. Re-adjustment of nailing depth is required.

INSPECTION AND MAINTENANCE

CAUTION

Be sure to disconnect the hose during cleaning

jams, inspection, maintenance and cleaning.

1. Countermeasure for nail jamming

(1) DISCONNECT AIR HOSE.

(2) Remove all nails.

(3) Release the lock lever and open guide plate (A) (See

Fig. 13).

(4) Remove the jammed nail with a slotted-head

screwdriver (See Fig. 14).

(5) Close guide plate (A) and latch.

(6) In case of frequent jams, consult the Authorized

Service Center from which you bought this machine.

2. Inspecting the magazine

Clean the magazine. Remove dust or wooden chips

which may have accumulated in the magazine. Apply

oil occasionally to the nail rail (See Fig. 15).

3. Check on mounting screws for each part

At regular intervals check every part for loose

mounting screws and whether or not there are any

air leaks. Retighten any loose screws. Operating the

equipment with loose screws untightened will incur

a hazard.

4. Inspecting the push lever

Check if the push lever (Fig. 1) can slide smoothly.

Clean up the sliding area of the push lever and use

the provided oil for lubrication from time to time.

Lubrication enables smooth sliding and

simultaneously serves to prevent the formation of

rust.

5. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

COMPRESSOR

CAUTION

When the maximum, operating pressure of the air

compressor exceeds 8.3 bar (120 psi.), be sure to

provide a reducing valve between the air compressor

and nailer. Then, adjust the air pressure within the

operating range of 4.9 – 8.3 bar (70 – 120 psi.). If the

air set is installed, lubrication is also possible, thus

providing additional convenience.

OILER-FILTER-REDUCING VALVE (Air Set)

So that the equipment can be operated under an optimum

condition to ensure extended service life, it is

recommended to use an oiler filter reducing valve. Please

limit the length of the hose between the unit and the air

set to within 10 m when using (See Fig. 16).

APPLICABLE LUBRICANTS

Type of lubricant Name of lubricant

Recommended oil SHELL TONNA

Motor oil SAE10W, SAE20W

Turbine oil ISO VG32 – 68

(#90 – #180)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NT65M2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info