Bedienungsanleitung Hitachi NV45AB2 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568902

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

(6) Lock the knob completely.

CAUTION

⅜ To prevent unitentional operation, never touch the

trigger or place the top end of the push lever on a work

bench or floor. Also, never face the nail outlet toward

any part of a person.

NOTE

⅜ Before loading the nails in the magazine, position the

nail holder according to the length of the nail. If the nail

holder position is not adjusted, the nail jam. If the

cover is forcibly closed without adjusting the position

of the nail holder, the nail holder may be damaged.

HOW TO USE THE NAILER

CAUTIONS:

⅜ Never use the head or body of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

1. Nailing procedures

NOTE

⅜ For nailing asphalt composition shingles the correct

air pressure is that which will drive the nail, so that the

underneath side of the nail touches or creases the top

surface of the shingle without breaking or cutting it.

This Nailer is equipped with the push lever and does not

operate unless the push lever is depressed (upward

position).

There are two methods of operation to drive nails with

this Nailer.

They are:

1. Intermittent operation (Trigger fire):

2. Continuous operation (Push lever fire):

(1) Intermittent operation (Trigger fire)

1 Position the nail outlet on the workpiece with

finger off the trigger.

2 Depress the push lever firmly until it is completely

depressed.

3 Pull the trigger to drive a nail.

4 Remove finger from the trigger.

To drive another nail, move the Nailer along the

workpiece and repeat this procedure. (Fig. 6)

Fig. 6

CAUTION

⅜ This tool will sometimes fire twice in rapid succession

when strongly pressed flush against a surface or

Push Lever

Trigger

when using on hard materials. In such cases, fire the

nails by squeezing and quickly releasing the trigger.

(2) Continuous operation (Push lever fire)

1 Pull the trigger with the Nailer off the workpiece.

2 Depress the push lever against the workpiece to

drive a nail.

3 Move the Nailer along the workpiece with a

bouncing motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been

driven, remove finger from the trigger. (Fig. 7)

Fig. 7

CAUTION:

Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

NOTES:

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the bumper, magazine, and nail feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all nails

should be removed after using this nailer.

⅜ After completing operation, put into the body about

2cc oil through the hose joint to protect the tool from

rust.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. Adjusting the nail-driving depth

CAUTIONS:

When making adjustments, be sure remove your

finger from the trigger. When making adjustments, be

sure that the nail outlet is not facing downward and

that body parts or other persons are not in the path of

the nail outlet.

To assure that each nail penetrates to the same depth, be

sure that:

1) the air pressure to the Nailer remains constant

(regulator is installed and working properly), and

2) the Nailer is always held firmly against the workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

1 DISCONNECT AIR HOSE FROM NAILER (Fig. 8)

Previously pull

the trigger

01Eng_NV45AB2_WE 3/24/09, 14:555

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV45AB2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info