Bedienungsanleitung Hitachi NV65AH (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568910

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English

NOTE:

Be careful not to deform the collated wires and not to

disengage the nails with the guide surface.

Otherwise, the nail guide will not close correctly.

4 Pulling the nails to the right, swing the nail guide

closed. (Fig. 6)

(7) Lock the knob completely.

HOW TO USE THE NAILER

CAUTIONS:

⅜ Never use the head or body of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

1. This Nailer is equipped with the push lever and does

not operate unless the push lever is depressed

(upward position).

There are two methods of operation to drive nails

with this Nailer.

They are:

1. Intermittent operation (Trigger fire)

2. Continuous operation (Push lever fire)

(1) Intermittent operation (Trigger fire)

1 Position the nail outlet on the workpiece with

finger off the trigger.

2 Depress the push lever firmly until it is completely

depressed.

3 Pull the trigger to drive a nail.

4 Remove finger from the trigger.

To drive another nail, move the Nailer along the

workpiece and repeat this procedure. (Fig. 7)

Fig. 7

(2) Continuous operation (Push lever fire)

1 Pull the trigger with the Nailer off the workpiece.

2 Depress the push lever against the workpiece to

drive a nail.

3 Move the Nailer along the workpiece with a

bouncing motion.

Each depression of the push lever will drive a

nail.

As soon as the desired number of nails have been

driven, remove finger from the trigger. (Fig. 8)

Fig. 8

CAUTION:

Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

NOTES:

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the bumper, magazine, and nail

feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all

nails should be removed after using this nailer.

⅜ After completing operation, put into the body about

2cc oil through the hose joint to protect the tool from

rust.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. Adjusting the nail-driving depth

CAUTIONS:

When making adjustments, be sure remove your

finger from the trigger. When making adjustments,

be sure that the nail outlet is not facing downward

and that body parts or other persons are not in the

path of the nail outlet.

⅜ Adjusting the adjuster (Fig. 9)

Carry out test driving. If the nails are too deep, turn

the adjuster to the shallow side (

mark).

If the nail depth is too shallow, turn the adjuster to

the deep side ( mark). (See Fig. 9, 10)

Depth is changed 1 mm with each rotation of the

adjuster.

Fig. 9

Adjuster

Deep

Shallow

Push Lever

Trigger

Previously pull

the trigger

01Eng_NV65AH_WE 9/11/11, 2:47 PM5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV65AH Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info