Bedienungsanleitung Hitachi NV75AG (Seite 11 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568911

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

3. Changing the exhaust direction

The direction of the exhaust vent can be changed by

turning the top cover (Fig. 13).

4. Cutting off the sheet

Tear off the output sheet in the direction of the arrow

when using the sheet collated nails (Fig. 14).

INSPECTION AND MAINTENANCE

CAUTION

Be sure to disconnect the hose during cleaning jams,

inspection, maintenance and cleaning.

1. Countermeasure for nail jamming

(1) Remove the nail roll from the magazine, open the

nail guide, insert a rod into the outlet and tap the rod

with a hammer (Fig. 15).

(2) Remove the jammed nail with slotted screwdriver

(Fig. 16).

(3) Cut off the defective part of the steel wire which links

the nails with cutting nippers, correct the deformation,

then load the nail roll in the magazine.

(4) In case of frequent jams, consult the Authorized

Service Center from which you bought this machine.

2. Check on mounting screws for each part

At regular intervals check every part for loose

mounting screws and whether or not there are any

air leaks. Retighten any loose screws. Operating the

equipment with loose screws untightened will incur

a hazard.

3. Inspecting the push lever

Check if the push lever can slide smoothly (Fig. 17).

Clean up the sliding area of the push lever and use the

provided oil for lubrication from time to time.

Lubrication enables smooth sliding and simultaneously

serves to prevent the formation of rust.

4. Inspecting the feeders

(1) Occasionally clean the knob sliding part and then

apply the recommended oil (See Fig. 18).

(2) Open the nail guide and remove dust, etc., as shown

in Fig. 19. Apply lubricant to the sliding groove of the

feeder and shaft. Check the nail stopper (A) and nail

stopper (B) slide smoothly by pushing them with

your finger.

(3) Also, apply the recommended oil to the feeding

surface of the nose and nail guide after cleaning. This

promotes smooth operation and retards corrosion.

CAUTION

Check for smooth movement of the feeders and

stoppers before use. If movement is uneven, nails

could be fired at an irregular angle, presenting a

hazard to the operator and others nearby.

5. Inspecting the magazine

Clean the magazine. Remove dust of wooden chips

which may have accumulated in the magazine.

6. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

COMPRESSOR

CAUTION

When the maximum, operating pressure of the air

compressor exceeds 8.3 bar (120 psi.), be sure to

provide a reducing valve between the air compressor

and nailer. Then, adjust the air pressure within the

operating range of 4.9 – 8.3 bar (70 – 120 psi.). If the

air set is installed, lubrication is also possible, thus

providing additional convenience.

OILER-FILTER-REDUCING VALVE (Air Set)

So that the equipment can be operated under an optimum

condition to ensure extended service life, it is advisable

to use an oiler filter reducing valve. Please limit the

length of the hose between the unit and the air set to

within 10m when using (Fig. 20).

APPLICABLE LUBRICANTS

Noise Information

Noise characteristic values in accordance with EN 792-

13, JUNE, 2000:

The typical A-weighted single-event sound power level

,1s,d = 105 dB.

The typical A-weighted single-event emission sound

pressure level at work station

,1s,d = 92 dB.

These values are tool-related characteristic values and

do not represent the noise development at the point of

use. Noise development at the point of use will for

example depend on the working environment, the

workpiece, the workpiece support and the number of

driving operations, etc.

Type of lubricant Name of lubricant

Recommended oil SHELL TONNA

Motor oil SAE10W, SAE20W

Turbine oil

ISO VG32 ~ 68

(#90 ~ #180)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV75AG Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info