Bedienungsanleitung Hitachi NV75HMC (Seite 16 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568912

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

English

Type of lubricant Name of lubricant

Recommended oil SHELL TONNA

Motor oil SAE10W, SAE20W

Turbine oil

ISO VG32 - 68

(#90 - #180)

(3) Also, apply the recommended oil to the feeding

surface of the nose and nail guide after cleaning. This

promotes smooth operation and retards corrosion.

CAUTION

Check for smooth movement of the feeders and

stoppers before use. If movement is uneven, nails

could be fired at an irregular angle, presenting a

hazard to the operator and others nearby.

5. Inspect the Trigger

Periodically clean the sliding parts of the trigger, and

make sure that the trigger moves smoothly (Fig. 24).

6. Inspecting the muffler

This Nailer has a built-in muffler in the exhaust to

reduce noise and stirred-up dust during exhaust.

When the mesh of the muffler is filled or the muffler

is damaged, replace the muffler with a new one. To

replace the muffler, contact our Authorized Service

Center (Fig. 25).

7. Inspecting the magazine

Clean the magazine. Remove dust of wooden chips

which may have accumulated in the magazine.

8. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

9. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

COMPRESSOR

CAUTION

When the maximum, operating pressure of the air

compressor exceeds 23 bar (320 psi.), be sure to

provide a reducing valve between the air compressor

and nailer. Then, adjust the air pressure within the

operating range of 12 – 23 bar (170 – 320 psi.). If the

air set is installed, lubrication is also possible, thus

providing additional convenience.

APPLICABLE LUBRICANTS

Noise Information

Noise characteristic values in accordance with EN 792-

13, JUNE, 2000:

The typical A-weighted single-event sound power level

,1s,d = 99.3 dB.

The typical A-weighted single-event emission sound

pressure level at work station

,1s,d = 92.4 dB.

Uncertainty KpA: 2.5 dB (A)

These values are tool-related characteristic values and

do not represent the noise development at the point of

use. Noise development at the point of use will for

example depend on the working environment, the

workpiece, the workpiece support and the number of

driving operations, etc.

Depending on the conditions at the workplace and the

form of the workpiece, individual noise attenuation

measures may need to be carried out, such as placing

workpieces on sound-damping supports, preventing

workpiece vibration by means of clamping or covering,

adjusting to the minimum air pressure required for the

operaion involved,etc.

In special cases it is necessary to wear hearing protection

equipment.

Vibration Information

The typical vibration characteristic value in accordance

with EN 792-13, JUNE, 2000 : 4.8 m/s

Uncertainty K = 1.5 m/s

This values is a tool-related characteristic value and

does not represent the influence to the hand-arm-system

when using the tool. An influence to the hand-arm-

system when using the tool will for example depend on

the gripping force, the contact pressure force, the working

direction, the adjustment of energy supply, the workpiece,

the workpiece support.

01Eng_NV75HMC_WE 3/13/12, 9:0815

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV75HMC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info