Bedienungsanleitung Hitachi NV90AB (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568914

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

HOW TO USE THE NAILER

CAUTIONS:

⅜ Never use the head or body of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

1. Nailing procedures

(1) Method of intermittently driving nails (single shot)

The single-contact change lever is in the single shot

position (See Fig. 8)

This nailer includes a single shot structure to allow

striking of a single nail by pushing down the push

lever and pulling the trigger (see Fig. 7).

CAUTION:

⅜ [Method of intermittently driving nails (single shot)]

explained here is not [Sequential fire]. When Single-

contact Change Lever is at the Single shot position, if

the push lever is pushed up in a state where the

trigger is pulled, only one piece of nail in the shooting

muzzle is fired: Be careful!

In the event it is used by Sequential fire, use the

Sequential Fire Parts Set of Optical Accessory.

⅜ If you do not pull the trigger quickly and crisply while

in the single shot mode, the nailer will bounce and

shoot several nails instead of just one. To avoid this,

be sure to pull the trigger quickly and crisply.

Fig. 7

Fig. 8

⅜ Push lever

When depressing the nail outlet, be sure to fully lift

the push lever (see Fig. 7) to release the safety lock.

Thus, nails cannot be driven without releasing the

safety lock even though the trigger is pulled.

(2) Method for continuous driving of nails (contact drive)

The single-contact change lever is in the contact

driving position (See Fig. 10).

Use the accessory hexagon bar wrench to turn the

single-contact change lever to the contact driving

position.

First pull back the trigger. Then press the nail outlet

on the place to drive nails. Driving of nails will start.

(Fig. 9)

Fig. 9

Fig. 10

CAUTION:

Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

NOTES:

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the bumper, magazine, and nail

feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all

nails should be removed after using this nailer.

⅜ After completing operation, put into the body about

2cc oil through the hose joint to protect the tool from

rust.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. How to use nosecap

CAUTION:

Remove the hose from the nailer and release the

compressed air before installing or removing the

nosecap to prevent accidental nail ejection.

⅜ Attach the nose cap (A) on the tip of the push lever

when you wish to protect the surface of wood, etc.,

from scratches.

Trigger

Push Lever

Contact Driving Position

Single-Contact

Change Lever

Single-Contact

Change Lever

Single Shot Position

Next, depress the

nail outlet

First, pull the Trigger

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV90AB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info