Bedienungsanleitung Hitachi NV90AB (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568914

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

Noise Information

Noise characteristic values in accordance with EN 792-

13, JUNE, 2000:

The typical A-weighted single-event sound power level

WA,1s,d = 99 dB

The typical A-weighted single-event emission sound

pressure levelat work station L

pA,1s,d = 90 dB.

These values are tool-related characteristic values and

do not represent the noise development at the point of

use. Noise development at the point of use will for

example depend on the working environment, the

workpiece, the workpiece support and the number of

driving operations, etc.

Depending on the conditions at the workplace and the

form of the workpiece, individual noise attenuation

measures may need to be carried out, such as placing

workpieces on sound-damping supports, preventing

workpiece vibration by means of clamping or covering,

adjusting to the minimum air pressure required for the

operaion involved,etc.

In special cases it is necessary to wear hearing protection

equipment.

Vibration Information

The typical vibration characteristic value in accordence

with EN 792-13, JUNE, 2000: 2.62m/s

This values is a tool-related characteristic value and

does not represent the influence to the hand-arm-system

when using the tool. An influence to the hand-arm-

system when using the tool will for example depend on

the gripping force, the contact pressure force, the working

direction, the adjustment of energy supply, the

workpiece, the workpiece support.

5. Inspecting the magazine

Clean the magazine. Remove dust of wooden chips

which may have accumulated in the magazine.

6. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When ot in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

COMPRESSOR

CAUTION:

When the maximum, operating pressure of the air

compressor exceeds 8.3 bar (120 psi.), be sure to

provide a reducing valve between the air compressor

and nailer. Then, adjust the air pressure within the

operating range of 4.9 ~ 8.3 bar (70 ~ 120 psi.). If the

air set is installed, lubrication is also possible, thus

providing additional convenience.

OILER-FILTER-REDUCING VALVE (Air Set)

So that the equipment can be operated under an optimum

condition to ensure extended service life, it is advisable

to use an oiler filter reducing valve. Please limit the

length of the hose between the unit and the air set to

within 10m when using.

Fig. 22

APPLICABLE LUBRICANTS

➡

Filter

Oiler

Reducing Valve

➡

Nailer

Side

Compressor

Side

Type of lubricant Name of lubricant

Recommended oil SHELL TONNA

Motor oil SAE10W, SAE20W

Turbine oil ISO VG32 ~ 68

(#90 ~ #180)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NV90AB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info