Bedienungsanleitung Hitachi RH650V (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

570708

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

STANDARD ACCESSORIES

1 Nozzle (round) ............................................................. 1

2 Nozzle (ﬂ at) ..................................................................1

3 Nozzle (curved surface) ...............................................1

4 Nozzle (glass protector) ...............................................1

5 Scraper (with grip) ........................................................1

6 Case .............................................................................1

Standard accessories are subject to change by area.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Peeling oﬀ paint

○ Softening adhesive

○ Removing putty from window frames

○ Forming resin pipes

○ Welding plastic

○ Heat wrapping using heat-shrink ﬁ lm.

○ Soldering

○ Drying work

○ Defrosting work

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the

power requirements speciﬁ ed on the product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

BASIC FUNCTIONS

1. Switch Operations and Temperature Adjustments

(Fig. 1, Fig. 2)

Slide the knob upward to activate the switch and enable

continual operations even when your ﬁ nger is removed.

Slide the knob downward as far as it will go to set the

switch at the [0] position and turn it oﬀ .

The position to which the switch is slid will alternate

between modes.

Switch [1] position:

Fixes the wind temperature at 50°C and enables the

wind power to be adjusted.

Switch [2] position:

Enables the wind temperature to be adjusted

between 50°C and 650°C, and enables the wind

power to be adjusted.

2. Adjusting the Temperature (Fig. 1, Fig. 2, Fig. 3)

The temperature can be adjusted between 50°C and

650°C when the switch is at the [2] position.

The temperature will rise by 10°C each time the

Increase Temperature button is pressed (to a maximum

of 650°C.)

Press the button continuously to increase the

temperature in increments of 10°C.

The temperature will decrease by 10°C each time the

Decrease Temperature button is pressed (to a minimum

of 50°C.)

The set temperature will be indicated on the display

when the Increase Temperature and Decrease

Temperature buttons are pressed, but this will return to

the hot wind temperature display after a few seconds.

The temperature will be ﬁ xed at 50°C when the switch is

at the [1] position, and adjustment is not possible.

This is used to quickly cool material that is heat-

warping and to cool the nozzle when it reaches high

temperatures after using the tool.

3. Wind Power Adjustment (Fig. 1, Fig. 3)

The wind power can be adjusted in ﬁ ve stages between

1 and 5. (0.25m

to 0.5m

)

Press the [+] button to increase wind power, and the [–]

button to decrease wind power.

The tool can be used with it stood pointing upward.

(Fig. 4)

CAUTION

Make sure the tool is placed on a stable surface so that

it won’t topple over when used pointing upward.

4. Attaching the Nozzle (Fig. 5)

CAUTION

The nozzle is extremely hot immediately after use, so

do not touch it.

NOTE

Make sure you do not drop the nozzle.

Replace the nozzle for a type that is suited to the job in hand.

Insert the nozzle supplied ﬁ rmly into the hot wind release

nozzle until it can go no further.

5. Temperature Settings

WARNING

○ Do not use the tool in the vicinity of volatile substances

(thinner, gasoline, etc.)

○ Do not bring the hot wind release nozzle in close

contact with your hands or face during use.

The nozzle is extremely hot immediately after use, so

do not touch it.

Set the temperature in consideration of the article to be

heated.

Also, pay attention to the surrounding material that will be

heated at the same time.

First of all, apply the hot wind from a distance while checking

that there are no changes in the article being heated, and

then move it closer until it reaches an appropriate distance.

Heating inﬂ ammable substances

(paper, wood, plastic, etc.)

Set the switch to the [1] position and apply the heat with

the nozzle at least 10cm away from the article being

heated.

Gently move the tip of the nozzle up, down, left and right

to apply the heat.

Applying heat constantly to one location may result in

malformation or the outbreak of smoke.

Heating non-ﬂ ammable substances

(metal, stone, concrete, etc.)

Set the switch to the [1] position, and if there are no

problems, move it to the [2] position.

Apply the heat with the nozzle at least 5cm away from

the article being heated.

Holding the nozzle too close may result in the tool

overheating, leading to malfunctions.

000Book_RH650V_WE.indb 7000Book_RH650V_WE.indb 7 2014/02/14 8:47:462014/02/14 8:47:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi RH650V Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info