Bedienungsanleitung Hitachi S18SA (Seite 5 von 22) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

570715

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

English

5. Fixing the side handle

Screw the side handle into the housing.

6. Confirm the lock lever.

Confirm that the lock lever is disengaged by push-

ing lock lever two or three times before switching

the power tool on (See Fig. 2).

PRACTICAL SANDER APPLICATION

1. Do not heavily push the sanding disc to the surface

to be ground. Grinding operation can be achieved

with the weight of the machine alone, so maintain

the sanding disc to an extent that it lightly touches

the surface to be ground. When the sanding disc

is pushed heavily, its revolving speed drops, cre-

ating an unevenly finished surface and causing

motor seizure from overload.

2. Rather than applying the entire disc surface to the

metal surface to be ground, use the sander by

inclining it approximately 15°~30° to grind with the

disc peripheral portion. (Fig. 1)

3. Switching on the sander

The switch is of the quick-break trigger system.

When the trigger is pulled, the switch turns on; and

when it is released, the switch turns off.

When it is desired to keep the power on for a

prolonged period in continuous use, the stopper

can be used to keep the switch on even after the

trigger has been released. (First pull the trigger, and

then press the stopper.) To turn the switch off, first

pull the trigger again to disengage the stopper.

4. Precaution after use

Do not lay the sander down immediately after using

on a place where there are many shavings, much

dirt and dust until it has completely stopped revolv-

ing.

CAUTION

When the disc sander is not in use, the power

source should be disconnected.

ATTACHMENT/REMOVAL OF SANDING DISC

(Fig. 2)

CAUTION: Be sure to switch power OFF and disconnect

the attachment plug from the receptacle to

avoid a serious accident.

(1) Attach washer, rubber pad and sanding disc on the

spindle, in that order.

(2) While pushing the lock lever with one hand, lock

the spindle by turning the rubber pad slowly with

the other hand.

Tighten the wheel washer by using the supplied

wrench.

SPECIFICATIONS

(110V, 115V, 120V, 127V, 220V, 230V, 240V)

650 W

4000/min

2.7 kg

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) 180mm Sanding Disc (Grain size: P50 or P16) ......... 1

(2) Rubber Pad ................................................................. 1

(3) Wrench ........................................................................ 1

(4) Side handle ................................................................. 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

(1) 180mm Sanding disc

⅜ There are eleven different kinds of sanding disc,

having grain sizes of P16, P20, P24, P30, P36, P40,

P50, P60, P80, P100, P120. When placing your order,

please specify the grain size of the disc desired.

Optional accessories are subject to change without no-

tice.

APPLICATIONS

⅜ Sanding metal surfaces.

⅜ Preliminary sanding of metal surfaces before paint-

ing, rust removal, removing old paint before re-

painting.

⅜ Finishing woodwork, correcting projections of tim-

bers from joints or assemblies.

⅜ Preliminary sanding of wood surfaces before apply-

ing paint.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized con-

forms to the power requirements specified on the

product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

Caution:

Damaged cord must be replaced or repaired.

4. Attaching sanding disc

For attachment/removal of the sanding disc, refer

to “ATTACHMENT/REMOVAL OF SANDING DISC”.

Many types of sanding discs are available; select

one appropriate to the work.

Voltage (by areas)*

Power Input*

No-load speed

Weight (without cord)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi S18SA Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info