Bedienungsanleitung Hitachi S18SB (Seite 6 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

512000

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

English

3. Switching on the sander

The switch is of the quick-break trigger system.

When the trigger is pulled, the switch turns on; and

when it is released, the switch turns off.

When it is desired to keep the power on for a

prolonged period in continuous use, the stopper

can be used to keep the switch on even after the

trigger has been released. (First pull the trigger, and

then press the stopper.) To turn the switch off, first

pull the trigger again to disengage the stopper.

4. Precaution after use

Do not lay the sander down immediately after using

on a place where there are many shavings, much

dirt and dust until it has completely stopped

revolving.

CAUTION

When the disc sander is not in use, the power

source should be disconnected.

ATTACHMENT/REMOVAL OF SANDING DISC

(Fig. 2)

CAUTION: Be sure to switch power OFF and disconnect

the attachment plug from the receptacle to

avoid a serious accident.

(1) Attach washer, rubber pad and sanding disc on the

spindle, in that order.

(2) While pushing the lock lever with one hand, lock

the spindle by turning the rubber pad slowly with

the other hand.

Tighten the wheel washer by using the supplied

wrench.

⅜ Remove the sanding disc in the reverse order to

attachment.

CAUTION:

Confirm that the lock lever is disengaged by pushing

lock lever two or three times before switching the

disc sander on.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws:

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

2. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

3. Inspecting the carbon brushes (Fig. 4)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brushes with new ones which have the same carbon

brush No. shown in the figure when they become

worn to or near the “wear limit”. In addition, always

keep carbon brushes clean and ensure that they

slide freely within the brush holders.

4. Replacing carbon brushes:

Disassemble the brush caps with a slotted-head

screwdriver. The carbon brushes can then be easily

removed.

5. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not

be applicable to other markets except The United

Kingdom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi S18SB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info