Bedienungsanleitung Hitachi SV 12 SD (Seite 7 von 45) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

79018

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

English

CAUTION

Never turn the power switch ON when the sander is

contacting the surface to be sanded. This is necessary

to preclude damage to the material. The same applies

when switching the power OFF.

2. How to hold the orbital sander

While gripping the knob with one hand and the handle

with the other, lightly press the sander against the

surface to be sanded so that the sanding paper

uniformly contacts the surface, as shown in Fig. 6.

DO NOT apply excessive pressure to the sander while

sanding. Excessive-pressure may cause overload of

the motor, reduced service life of the sanding paper,

and lowered sanding or polishing efficiency.

3. How to move the orbital sander

For optimum operating efficiency, alternately move

the sander forward and backward at a constant speed

and balance.

4. Changing the rotating Speed (model SV12V only)

SV12V has an electronic control system which can be

use to set the rotating speed between 4000 and 10000

revolutions per minute.

As shown in Fig. 7, dial position “1” is for minimum

speed and position “5” for maximum speed.

MOUNTING THE OPTIONAL ACCESSORIES

1. Mounting the magic pad.

Loosen the six screws.

Remove the pad and attach the magic pad.

CAUTION

Replace the pad only. Use the other parts without

removing them.

2. Mounting the cleaner adapter (for models SV12V

and SV12SD) (Fig. 8).

After mounting the dust collector hose onto the

cleaner adapter, mount the cleaner adapter onto the

unit in the same way as mounting the dust bag.

MAINTENANCE AND INSPECTION

1. Empting and cleaning the Dust Bag (for models

SV12V and SV12SD)

If the dust bag contains too much saw dust, dust

collection will be affected. Empty the dust bag when

it gets full.

Remove the dust bag, open the fastener, and dispose

of the contents.

2. Inspecting the sanding paper

Since use of worn-out sanding paper will degrade

efficiency and cause possible damage to the pad, replace

the sanding paper as soon a excessive abrasion is noted.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

4. Inspecting the carbon brushes (Fig. 10)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with a new one having the same carbon brush

No. shown in the figure when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely within

the brush holders.

5. Replacing carbon brushes

⅜ Disassembling

(1) Loosen the two screws on the top cover, and remove

the top cover. (Fig.11)

(2) Lift out the brush holder together with the carbon

brush, while being very careful not to forcibly pull

the internal wires within the brush holder.

(3) Remove the carbon brush from the brush holder.

⅜ Reassembling

(1) Insert the brush terminal into the brush holder. Turn

the brush terminal 90˚.

(2) While maintaining this brush terminal position as

explained in (1), insert the new carbon brush into the

brush holder.

(3) While pressing the carbon brush against the outside

wall of the housing's bearing compartment, insert

the brush holder into the housing's original position.

(4) Place the internal wire in the specified position. Be

very careful not to allow the internal wire to contact

the armature or rotating parts of the motor. (Fig. 12)

(5) Replace the top cover, while being careful to ensure

it does not pinch the internal wire, and secure it

firmly with the two screws.

CAUTION

Should the internal wire be pinched by the top cover

or come in contact with the armature or rotating

parts of the motor, a serious danger of electric shock

to the operator will be created. Exercise extreme

caution in disassembling and reassembling the motor,

following the above procedure exactly.

DO NOT attempt disassemble any parts other than

those necessary to effect replacement of the carbon

brush.

6. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi SV 12 SD Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi SV 12 SD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info