Bedienungsanleitung Hitachi SV 12 SG (Seite 17 von 21) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78498

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

English

SPECIFICATIONS

Voltage (by areas)* (110V, 120V, 220V, 230V, 240V)

Power Input* 200 W

No-Load Speed 14000 min

–1

Sanding pad size 110 mm × 100 mm

Sanding paper size 114 mm × 140 mm

Weight (without cord) 1.1 kg

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

⅜ Sanding paper ............................................................ 1

⅜ Dust bag ...................................................................... 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

1. Sanding paper

⅜ 114 × 140 mm paper clip type sanding paper

Grain: AA60, AA100, AA150

⅜ 110 × 100 mm Velcro type sanding paper

Grain: AA60, AA100, AA150

⅜ 110 × 100 mm stick-on type sanding paper

Grain: AA60, AA80, AA100, AA120, AA150, AA180

⅜ Outer diameter 125 mm stick-on type sanding paper

Grain: AA60

2. Sanding pad

⅜ 110 × 100 mm sponge pad (Velcro type)

⅜ 110 × 100 mm stick-on pad

⅜ Outer diameter 125 mm stick-on pad

3. Punch plate

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Finish polishing of woodwork surfaces

⅜ Sanding surfaces of woodwork or sheet metal prior

to painting, etc.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a power receptacle while

the power switch is in the ON position, the power

tool will start operating immediately, which could

cause a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Installing the sanding paper

(1) Bending the sanding paper:

Position the sander with its pad side facing upward

as shown in Fig. 1. Place the sanding paper on the

pad so that the center of the sanding paper is aligned

with the center of the pad, and bend both ends of the

sanding paper at a 90° angle. Then, bend both ends

again in the manner shown in Fig. 2. The sanding

paper is now ready to be installed on the sander.

(2) Installing the sanding paper:

While ensuring that the cord is not bent, place the

sander on a workbench as shown in Fig. 3, and insert

one end of the sanding paper (bent section). Next,

insert the remaining bent section in the same manner.

CAUTION

The sanding paper must be precisely installed on the

pad, ensuring that there is ample tension (leaving no

slack). Loosely installed sanding paper could result

in unevenly sanded surfaces and/or damage to the

sanding paper itself.

5. Attaching and Removing the Dust Bag

(1) Attaching the Dust Bag

As shown in Fig. 4, hold the dust gate and push it in

the direction of Arrow A to attach it to the dust outlet.

(2) Removing the Dust Bag

As shown in Fig 4, hold the dust gate and pull it in the

direction of Arrow B to remove it from the dust

outlet.

CAUTION

Prior to the sanding operation, make sure the material

of surface you are going to sand.

If the surface under sanding operation is expected to

generate harmful / toxic dusts such as lead painted

surface, make sure the dust bag or appropriate dust

extraction system is connected with dust outlet tightly.

Wear the dust mask additionally, if available.

Do not inhale or touch the harmful / toxic dusts

generated in sanding operation, the dust can

endanger the health of yourself and bystanders.

PRACTICAL OPERATING PROCEDURES

CAUTION

Never apply water or grinding fluid when sanding. This

could result in electrical shock.

1. Switching the sander ON and OFF

The power can be turned on by setting the lever to

ON (1) and turned off by setting the lever to OFF (0).

CAUTION

Never turn the power switch ON when the sander is

contacting the surface to be sanded. This is neces-

sary to preclude damage to the material. The same

applies when switching the power OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi SV 12 SG Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi SV 12 SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info