Bedienungsanleitung Hitachi TCS33EB (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

661497

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

Depth gauge setting File guide angle

Side plate ﬁ ling angle

File

Top plate angle

Depth gauge

NOTE: Noise level/vibration levels are calculated as the time-weighted energy total for noise/vibration levels under various

working conditions with the following time distribution:

: 1/3 idle, 1/3 full, 1/3 racing speed.

: 1/2 full, 1/2 racing speed.

WHAT IS WHAT? (Fig. 1)

A: Throttle lever: Device activated by the operatorʼs ﬁ nger,

for controlling the engine speed.

B: Throttle lever lockout: Device that prevents the

accidental operation of the throttle lever until manually

released.

C: Stop switch: Device for allowing the engine to be started

or stopped.

D: Oil tank cap: For closing the oil tank.

E: Recoil starter: Pull handle to start the engine.

F: Front handle: Support handle located at or towards the

front of the engine housing.

G: Fuel tank cap: For closing the fuel tank.

H: Rear handle: Support handle located at or towards the

rear of the engine housing.

I: Choke lever: Device for enriching the fuel/air mixture in

the carburetor, to aid starting.

J: Priming pump: Device for supplying extra fuel, to aid

starting.

K: Guide bar: The part that supports and guides the saw

chain.

L: Saw chain: Chain, serving as a cutting tool.

M: Chain brake (Front hand guard): Device for stopping or

locking the chain.

N: Chain catcher: device for restraining the saw chain.

O: Air ﬁ ler cover: Cover for air ﬁ lter and carburetor.

P: Side case: Protective cover to the guide bar, saw chain,

clutch and sprocket when the chain saw is in use.

Q: Tension adjustment bolt: Device, often acting on the

guide bar, for adjusting the saw chain tension.

R: Muﬄ er: Reduces engine exhaust noise and directs the

exhaust gases.

S: Anti-vibration rubber: Reduce the transmission of

vibrations to the operator's hands.

T: Chain bar clamp nut: Secures the side case and the

guide bar.

U: Spiked bumper: Device for acting as a pivot when in

contact with a tree or log.

V: Guide bar cover: Device for covering the guide bar and

saw chain when the unit is not being used.

W: Combi box spanner: The tool for removing or installing a

spark plug and tensioning the saw chain.

X: Handling instructions: Included with unit. Read before

operation and keep for future reference to learn proper,

safe techniques.

WARNINGS AND SAFETY

INSTRUCTIONS

Pay special attention to statements preceded by the

following words:

WARNING

Indicates a strong possibility of severe personal injury or

loss of life, if instructions are not followed.

CAUTION

Indicates a possibility of personal injury or equipment

damage, if instructions are not followed.

NOTE

Helpful information for correct function and use.

Operator safety

○ Always wear a safety face shield or goggles.

○ Gloves should be used when sharpening chain.

○ Always wear safety protective equipment such as

jacket, trousers, gloves, helmet, boots with steel toe-

caps and non-slip soles, and eye, ear and leg protection

equipment whenever you use a chain saw. For working

in trees the safety boots must be suitable for climbing

techniques. Ask Tanaka dealer for help in choosing the

right equipment. Do not wear loose clothing, jewelry,

short pants, sandals or go barefoot.

Secure hair so it is above shoulder length.

○ Do not operate this tool when you are tired, ill or under

the inﬂ uence of alcohol, drugs or medication.

○ Never let a child or inexperienced person operate the

machine.

○ Wear hearing protection. Pay attention to your

surroundings.

Be aware of any bystanders who may be signaling a

problem.

Remove safety equipment immediately upon shutting oﬀ

engine.

○ Wear head protection.

○ Never start or run the engine inside a closed room or

building.

Breathing exhaust fumes can be fatal.

○ For respiratory protection, wear a protection mask while

emitting the chain oil mist and dust from sawdust.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting equipment.

○ When the unit is shut oﬀ , make sure the cutting

attachment has stopped before the unit is set down.

○ When operation is prolonged, take a break periodically

so that you may avoid possible Hand-Arm Vibration

Syndrome (HAVS) which is caused by vibration.

○ National regulation can restrict the use of machine.

○ The operator must obey the local regulations of cutting

area.

WARNING

○ Antivibration systems do not guarantee that you will not

sustain Hand-Arm Vibration Syndrome or carpal tunnel

syndrome.

Therefore, continual end regular users should monitor

closely the condition of their hands and ﬁ ngers. If any

of the above symptoms appear, seek medical advice

immediately.

○ Long or continuous exposure to high noise levels may

cause permanent hearing impairment. Always wear

approved hearing protection when operating a unit/

machine.

000Book_TCS33EB_WE.indb 8000Book_TCS33EB_WE.indb 8 2017/02/22 10:02:342017/02/22 10:02:34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi TCS33EB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info