Bedienungsanleitung Hitachi UC9SC (Seite 5 von 14) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571409

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

English

CHARGING

Before using the power tool, charge the battery as

follows.

1. Insert the battery in the charger.

Position the battery so that the nameplate faces

toward the nameplate of the charger and press in

the battery until it comes into contact with the

bottom plate. (See Figs. 1 and 2)

2. Connect the charger power cord to the AC outlet.

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the AC outlet and check the

battery mounting condition.

About 1 hour is required to fully charge the battery

at a temperature of about 20°C. The pilot lamp goes

off to indicate that the battery is fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than four hour has passed after start of the charging,

stop the charging and contact your HITACHI

AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light. At that time cool the battery first,

then start charging.

3. Disconnect the charger power cord from the AC

outlet.

4. Hold the charger tight and pull out the battery.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Fail-

ure to do so could result in serious hazard.

2. Cleaning of the charger

When the charger is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for

they melt plastics.

3. Store idle charger

When not in use, the charger should be stored in

dry, high or locked-up place–out of reach of children.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: – Neutral

Brown: – Live

As the colours of the wires in the mains lead of this tool

may not correspond with the coloured markings identify-

ing the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the termi-

nal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi UC9SC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info