Bedienungsanleitung Hitachi VB16Y (Seite 10 von 70) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571640

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

English

HOW TO USE (CUTTING)

WARNING!

⅜ Note that the unit is not a hand held tool. Be

absolutely sure to use the unit only after placing

it on stable spots such as floor, ground, etc.

⅜ Never bring your hand close to the cutter during

operation.

⅜ Never bring your hand close to the reaction stoppers

A and B during operation.

⅜ Do not cut any materials other than the rebars. If

you attempt to do so, the material can splinter into

pieces and scatter.

⅜ The bending roller moves even during cutting

operation. Never bring your hand close to the

bending roller.

⅜ The cutter blade can get worn out by repeated

cutting of the rebar. Continued use of a worn-out

cutter can result in the damage and the broken

pieces flying around. Replace it with a new cutter

after approximately 8,000 times of cutting as a

rough guide.

⅜ The machine is so designed that the upper cutter

and the grip rubber can support a rebar.

If the grip rubber gets worn out, there is a fear that

it cannot sufficiently hold the rebar and gets broken

down with its parts flying around, etc.

If the grip rubber cannot hold the rebar much

longer, replace it with a new grip rubber. (For

replacing the grip rubber and repairing, ask the

store where you purchased it or the Hitachi Koki

Power Tool Center.)

● The cutter blade can get worn out by repeated rebar cutting. Continued use

of a worn-out cutter can result in the damage and the broken pieces flying

around. Replace it with a new cutter after approximately 8,000 times of cutting

as a rough guide.

● The machine is so designed that the upper cutter and the grip rubber can

support a rebar.

If the grip rubber gets worn out, there is a fear that it cannot sufficiently hold

the rebar and gets broken down with its parts flying around, etc.

If the grip rubber cannot hold the rebar much longer, replace it with a new

grip rubber.

● During cutting work, securely hook the rebar to the reaction stopper B.

Furthermore, secure enough length of a rebar to be hooked to the reaction

stopper B.

● Avoid bringing your hand near to the reaction stopper B during operation;

otherwise, you may get your finger caught in or may run the hazard of other

injuries.

● Set the rebar in the center or the recess of the cutter during cutting work.

Any cutting work with the rebar set on corners or ends of the cutter can result

in the pieces of broken rebar flying around or the damage to the cutter and

the machine.

● If you bend the rebar with a large angle while placing your hand onto it,

there is a fear of getting your hand caught in by the fold-back reaction of

the rebar. Never place your hand onto the position where the rebar may

fold back.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi VB16Y Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info