Bedienungsanleitung Hitachi w 8 vb (Seite 23 von 26) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

381303

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

3. Plastic case 4. Hook

Optional accessories are subject to change without

notice.

APPLICATIONS

⅜ Tightening hex-head screws

⅜ Tightening drywall screws, wood screws and self-

drilling screws.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, inviting serious

accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Confirm the direction of bit rotation (Fig.1)

The bit rotates clockwise (viewed from the rear

side) when the reversing switch lever is set to the

“R” side position. When the lever is set to the “L”

side position, the bit rotates counterclockwise and

can be used to loosen and remove screws.

5. Adjusting the tightening depth (Fig.2)

Pull the lock sleeve in the direction of arrow to

remove it from the spline installed in the gear

cover. While pulling the lock sleeve and turning it

right and left, adjust the position of locator. Push

the lock sleeve and align the gear cover spline with

the lock sleeve spline.

The lock sleeve can be inserted onto the gear cover

spline and locked.

(1) For hex-head screws:

Mount a hex-head screw on the hex-socket and set

the distance between the sub-stopper end and the

screw head neck to 1 – 1.5 mm, as shown in Fig.3.

(2) For drywall screws:

Mount a drywall screw on the bit, and set the

distance between the sub-stopper end and the screw

head to 1.5 – 2 mm, as shown in Fig.4.

(3) For cross-recessed self-drilling screws:

Mount a self-drilling screw on the bit, and set the

distance between the sub-stopper end and the screw

head bottom to 1 – 1.5 mm, as shown in Fig.5.

6. Mounting the bit

For details, refer to the item “Mounting and

dismounting the bit”.

MOUNTING AND DISMOUNTING THE HEX-

SOCKET OR THE BIT

1. Dismounting the hex-socket (Fig.6)

(1) While rotating the Sub-Stopper pull it out from the

locator.

(2) Remove the hex-socket, hold it with the opposite

side of bit by hand or vise and pull out the bit with

pliers.

2. Dismounting the bit (Fig.7)

Remove sub-stopper (A) as the same manner of

hex-head socket and remove the bit holder, then

pull out the bit with pliers.

3. Dismounting the bit (Fig.8)

Remove the sub-stopper (C) as the same manner

of hex-head socket and remove the bit holder, then

pull out the bit with pliers.

4. Mounting the hex-socket or the bit

Install the bit in the reverse order to removal.

HOW TO USE THE SCREW DRIVER

1. Switch operation and rotational speed

adjustment

Bit rotational speed can be adjusted between 0 –

4000/min (W6V3) or 0 – 2600/min (W6VA3, W6VB2)

or 0 – 1700/min (W8VB) varying the degree by

which the trigger switch is pulled. Rotational speed

increases as the trigger switch is pulled, and reaches

a maximum speed of 4000/min (W6V3) or 2600/min

(W6VA3, W6VB2) or 1700/min (W8VB) when the

trigger switch is pulled fully.

To facilitate continuous operation, pull the trigger

switch and depress the switch stopper. The switch

will then remain ON even when the finger is released.

By pulling the trigger switch again, the switch

stopper disengages and the switch is turned OFF

when the trigger switch is released.

2. Screw Driver operation

When the switch is turned ON, the motor starts to

run but the hex-socket (or the bit) does not rotate.

Attach the hex-socket to the screw head groove,

and push the Screw Driver against the screw. The

hex-socket then rotates and tightens the screw.

CAUTION

Ensure that the Screw Driver is held truly

perpendicular to the head of the screw.

If held at an angle, the driving force will not be

fully transferred to the screw, and the screw head

and/or hex-socket will be damaged. Hex-socket

rotation stops when pushing force is released.

3. Direction of hex-socket rotation

The hex-socket rotates clockwise (viewed from the

rear side) when the reversing switch lever is set

to the “R” side position. When the lever is set to

the “L” side position, the hex-socket rotates counter-

clockwise, and can be used to loosen and remove

screws.

CAUTION

Never change the direction of hex-socket (or bit

holder) rotation while the motor is running. To do

so would seriously damage the motor. Turn the

power switch OFF before changing the direction

of hex-socket (or bit holder) rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi w 8 vb Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi w 8 vb

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info