Bedienungsanleitung Hitachi WF 4 DY (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78945

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English

CAUTION

If the guide sleeve does not return to its original

position, then the driver bit is not installed properly.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the condi-

tions laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it

is at all loose it can drop and cause an accident.

3. Preparing the screws

Select screws appropriate to the application.

4. Bit checking and replacement

A No. 2 Plus bit is installed on this machine as a

standard accessory. Always inspect the bit to make

sure it is not damaged. Using worn bits can cause

screw-in malfunctions. Inspect the bit before work

and quickly replace it with a new one when it starts

to wear out. When the bit must be replaced due

to bit damage or any other reason, replace it

according to the instructions in Bit installation and

removal.

SCREW LENGTH AND SCREW-IN DEPTH

ADJUSTMENT

The tightening depth of this machine can be adjusted by

rotating the knob.

The tightening depth is adjusted by rotating the knob and

setting the stopper to the numerals (screw length) indicated

on the slider case.

Select a top adjuster to match screw length to be used and

attach it to the top edge. (Refer to Fig. 9)

Store the top adjuster in the storage room on the side face

of the slider case when it is not used.

The top adjuster is stored easily when the button shown in

Fig. 8 is pressed.

(1) In case that you use a screw which has a length

of 25-32 mm (L), please use the top adjuster No.

1 (small).

(2) In case that you use a screw which has a length

of 35-41 mm (L), please use the top adjuster No.

2 (large).

[Fine adjustment of tightening depth]

The tightening depth adjustments (1) to (2)

mentioned above are just preliminary.

Perform fine adjustment after trial driving.

Rotate the knob in

direction when the screw

head is too high.

Rotate the knob in direction when the screw

head is too low.

(Refer to Fig. 11)

COLLATED SCREW STRIPS INSTALLATION

AND REMOVAL

1. Installation

(1) Insert the tape tip of collated screw strips into the

belt guide groove (A section).

(2) Next, insert the tape tip into the slider groove (B

section) and feed to push in the \ direction.

(Fig. 12, Fig. 13 and Fig. 15)

(3) Set the collated tape so that the first screw is lined

up with the slider screw mark. (Fig. 14 and Fig. 15).

Driver bit

No. 2

(114L)

Anvil

hexagonal

hole

Top adjuster storage (rear side)

Fig. 8

Button

Top adjuster

No. 1 (small)

Stopper

Knob

Raise

Lower

Match the

stopper to

the screw

length

(25–32).

Fig. 9

Top adjuster

No. 2 (large)

Stopper

Knob

Fig. 10

Match the

stopper to the

screw length

(35–41).

Correct

(Flush)

Too high

Too low

Fig. 11

Fig. 7

Guide

sleeve

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WF 4 DY Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info