Bedienungsanleitung Hitachi WH10DFL (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

571650

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

English

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may create a risk

of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

PRECAUTIONS FOR CORDLESS IMPACT

DRIVER

1. This is portable tool for tightening and loosenig

screws. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. After installing the driver bit, pull lightly out the bit

to make sure that it does not come loose. If the bit is

not installed properly, it can come loose during

use, which can be dangerous.

5. Use the bit that matches the screw.

6. Tightening a screw with the impact driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted

to the screw. Tighten with this impact driver lined

up straight with the screw.

7. Always charge the battery at a temperature of 0 –

40°C. Charging the battery at temperatures outside

the range of 0 – 40°C may prevent proper charging

and reduce battery life.

The most suitable temperature for charging is that

of 20 – 25°C.

8. When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

Do not charge the battery more than 2 hours.

9. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

10. Never disassemble the rechargeable battery and

charger.

11. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

12. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

13. When drilling in wall, floor or ceiling, check for

buried electric power cord, etc.

14. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose

of the exhausted battery.

15. Using an exhausted battery will damage the charger.

16. Do not insert object into the air ventilation slots of

the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor

may stop. This is not the trouble but the result of

protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

⅜ During work make sure that swarf and dust do not

fall on the battery.

⅜ Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.

⅜ Do not store an unused battery in a location exposed

to swarf and dust.

⅜ Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it together

with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

01Eng_WH10DFL_WE 1/16/09, 11:025

Hitachi WH10DFL Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info