Bedienungsanleitung Hitachi WH12DAF2 (Seite 12 von 94) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572110

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

English

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you. (Fig. 12)

(3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(b) The direction of the light can be adjusted within

the range of hook positions 1 - 5. (Fig. 13)

⅜ Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION:

Do not look directly into the light.

Such actions could result in eye injury.

(4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1). (Fig. 14)

Remove the hook cover by pushing in the direction

of the arrow. (Fig. 15)

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly. (Fig. 16)

the protuberance of the hook cover, press the

hook cover in the direction opposite to that of the

arrow shown in Fig. 15 and then tighten the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE:

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION:

⅜ Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

⅜ Do not discard batteries together with normal trash

and do not throw batteries into fire.

⅜ Store batteries out of the reach of children.

⅜ Use batteries correctly in accordance with the battery

specifications and indications.

2. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise. (See Fig. 17) (The

and

marks

are provided on the body.)

CAUTION:

The push button cannot be switched while the impact

driver is turning. To switch the push button, stop the

impact driver, then set the push button.

3. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

4. Tightening and loosening screws (WH12DAF2)

Install the bit that matches the screw, line up the bit

in the grooves of the head of the screw, then tighten

it.

Push the impact driver just enough to keep the bit

fitting the head of the screw.

CAUTION:

Applying the impact driver for too long tightens the

screw too much and can break it.

Tightening a screw with the impact driver at an angle

to that screw can damage the head of the screw and

the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with

the screw.

5. Number of screws tightenings possible (WH12DAF2)

Please refer to the table below for the number of

screw tightened possible with one charge.

EB1214S

These values may vary slightly, according to

surrounding temperature and battery characteristics.

6. Number of bolt tightened possible (WR12DAF2)

Please refer to the table below for the number of bolt

tightened possible with one charge.

EB1214S

These values may vary slightly, according to

surrounding temperature and battery characteristics.

NOTE:

The use of the battery EB1226HL in a cold condition

(below 0 degree Centigrade) can sometimes result in

the weakened tightening torque and reduced amount

of work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

NOTE:

Do not touch the hammer case, as it gets very hot

during continuous work.

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low

speed rotation) and the motor is stopped while

continuously driving in screws, the components of

the electronic circuit parts may overheat and be

damaged.

3. Tightening torque

Refer to Fig. 18 and Fig. 19 for the tightening torque

of bolts (according to size), under the conditions

shown in Fig. 20. Please use this example as a general

reference, as tightening torque will vary according to

tightening conditions.

Bolt used No. of tightenings

M12 × 45 High tension bolt

Approx. 87

Screw used No. of tightenings

Wood screw ø4 × 50

Approx. 190

(Soft wood)

Machine screw M8 × 16

Approx. 500

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WH12DAF2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info