Bedienungsanleitung Hitachi wh12dm2 (Seite 59 von 74) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

381174

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose power

tools and charger to rain. Don’t use power tools

and charger in damp or wet locations. And keep

work area well lit. Never use power tools and charger

near flammable or explosive materials. Do not use

tool and charger in presence of flammable liquids

or gases.

3. The appliance is not intended for use by young

children or infirm persons without supervision.

Young children should be supervised to ensure

that they do not play with the appliance. All visitors

should be kept safe distance from work area.

4. Store idle tools and charger. When not in use, tools

and charger should be stored in dry, high or locked-

up place-out of reach of children and infirm persons.

Store tools and charger in a place where the

temperature is less than 40˚C.

5. Don’t force tool. It will do the job better and safer at

the rate for which it was designed.

6. Use right tool. Don’t force small tool or attachment

to do the job of a heavy duty tool.

7. Wear proper apparel. Do not wear clothing or

jewelry. They can be caught in moving parts. Rubber

gloves and footwear are recommended when

working outdoor.

8. Use eye protection with most tools. Also use face

or dust mask if cutting operation is dusty.

9. Don’t abuse cord. Never carry charger by cord or

yank it to disconnect from receptacle. Keep cord

from heat, oil and sharp edges.

10. Secure work. Use clamps or a vise to hold work. It’s

safer than using your hand and it frees both hands

to operate tool.

11. Don’t overreach. Keep proper footing and balance

at all times.

12. Maintain tools with care. Keep tools sharp at all

times, and clean for best and safest performance.

Follow instructions for lubricating and changing

accessories.

13. When the charger is not in use, or when being

maintained and inspected, disconnect its power

cord from the AC outlet.

14. Remove chuck wrenches and wrenches. Form habit

of checking to see that wrenches are removed from

tool before turning it on.

15. Avoid accidental starting. Don’t carry tool with finger

on switch.

16. To avoid danger, always use only the specified

charger.

17. Use only original HITACHI replacement parts.

18. Do not use power tools for applications other than

those specified in the Handling Instructions.

19. To avoid personal injury, use only the accessories

or attachment recommended in these handling

instructions or in the HITACHI catalog.

20. If the supply cord of this charger is damaged, the

charger must be returned to the HITACHI authorized

service center for the cord to be replaced. Let only

the authorized service center do the repairing. The

Manufacturer will not be responsible for any

damages or injuries caused by repair by the

unauthorized persons or by mishandling of the tool.

21. To ensure the designed operational integrity of

power tools and charger, do not remove installed

covers or screws.

22. Always use the charger at the voltage specified on

the nameplate.

23. Do not touch movable parts or accessories unless

the battery has been removed.

24. Always charge the battery before use.

25. Never use a battery other than that specified. Do

not connect a usual dry cell, a rechargeable battery

other than that specified or a car battery to the

power tool.

26. Do not use any transformer that has a booster.

27. Do not charge the battery from an engine electric

generator or DC power supply.

28. Always charge indoors. Because the charger and

battery heat slightly during charging, charge the

battery in a place not exposed to direct sunlight;

where the humidity is low and the ventilation good.

29. When working in a high place, pay attention to the

activities below to make sure there are no people

below.

30. Use the exploded assembly drawing on this

handling instructions only for authorized servicing.

31. If the supply cord is damaged, it must be replaced

by the manufacture or its service agent or a similarly

qualified person in order to avoid a hazard.

PRECAUTIONS FOR CORDLESS IMPACT

DRIVER

1. This is portable tool for tightening and loosening

screws. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. After installing the driver bit, pull lightly out the bit

to make sure that it does not come loose. If the bit is

not installed properly, it can come loose during

use, which can be dangerous.

5. Use the bit that matches the screw.

6. Tightening a screw with the impact driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted

to the screw. Tighten with this impact driver lined

up straight with the screw.

7. Always charge the battery at a temperature of 0 –

40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

8. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

9. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

10. Never disassemble the rechargeable battery and

charger.

11. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

Hitachi wh12dm2 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi wh12dm2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info