Bedienungsanleitung Hitachi wh12dm2 (Seite 64 von 74) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

381174

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English

3. Extension bar: WR12DM2: Code No. 873633

WR9DM2: Code No. 996143

The extension bar is convenient for working in very

restricted spaces or when the socket provided cannot

reach the bolt to be tightened.

CAUTION:

When the extension bar is used, the tightening torque

is reduced slightly compared with the ordinary socket.

4. Universal joint: WR12DM2: Code No. 992610

WR9DM2: Code No. 996147

The universal joint is convenient for impacting nuts

when there is an angle between the socket and

wrench, or when working in a very narrow space.

5. Duct Socket: (WR12DM2)

This is used for tightening bolts and nuts on flange

sections of air conditioners, type ducts, etc.

6. Corner attachment (Model EW-14R) (WR12DM2)

Use this attachment only when the machine is applied

to the nut or bolt at the right angle.

7. Bit adaptor: Code No. 322752 (WR12DM2)

This is used for tightening small screws (M6 – M8).

NOTES:

(1) This adaptor is set only on the anvil (drive angle) of

the main unit. The bit adapter cannot be attached to

the special accessory anvil (square drive).

(2) Before starting work with the adapter, tighten a few

screws with it to make sure it’s tightening with the

appropriate torque.

Code No.

Hexagonal width

across flats (mm)

993658 12

992613 13

992615 14

(3) Tightening speed will be greatly reduced when driving

wood, tapping or other similar screws.

Optional accessories are subject to change without notice.

APPLICATION

<WH12DM2, WH9DM2>

⅜ Driving and removing of small screws, small bolts,

etc.

<WR12DM2, WR9DM2>

⅜ Tightening and loosening of all types of bolts and

nuts, used for securing structural items.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery. (Figs. 1 and 2)

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals).

2. Insert the battery into the charger.

Insert the battery firmly, in the direction shown in

Fig. 3 and 4, until it contacts the bottom of the charger

compartment.

CAUTION:

⅜ If the battery is inserted in the reverse direction, not

only recharging will become impossible, but it may

also cause problems in the charger such as deformed

recharging terminal.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously

in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals.) (See

Table 5)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 5, according to the condition of the charger or

the rechargeable battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi wh12dm2 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi wh12dm2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info