Bedienungsanleitung Hitachi WH14DL2 (Seite 6 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572135

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle 3 tightly and push the battery latch

2 to remove the battery 1 (See Fig. 1 ).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery 1 while observing its polarities

(See Fig. 1).

CHARGING

Before using the impact driver or impact wrench, charge

the battery as follows.

1. Connect the charger’s power cord to a receptacle

When the power cord is connected, the charger’s

pilot lamp will blink in red (At 1-second intervals).

2. Insert the battery into the charger

Insert the battery firmly, until it contacts the bottom of

the charger compartment.

CAUTION

⅜ If the battery is inserted in the reverse direction, not

only recharging will become impossible, but it may

also cause problems in the charger such as deformed

recharging terminal.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light up

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red (At 1-second intervals) (See

Table 1).

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or

the rechargeable battery.

Charger

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 and 2 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

Cordless Impact Wrench

Model WH14DL WH18DL

Voltage 14.4 V 18 V

No-Load speed 0 – 2600 min

-1

Capacity (Ordinary bolt) M6 – M14

Tightening torque (Maximum) 140 N·m 150 N·m

Rechargeable battery 3.0 Ah

EBL1430: Li-ion (4 cells)

EBM1830: Li-ion (10 cells)

BCL1430: Li-ion (4 or 8 cells)

Weight 1.5 kg 1.6 kg

Model WR14DL WR18DL

Voltage 14.4 V 18 V

No-Load speed 0 – 2600 min

-1

Capacity (Ordinary bolt) M10 – M16

Tightening torque (Maximum) 200 N·m 220 N·m

Rechargeable battery 3.0 Ah

EBL1430: Li-ion (4 cells)

EBM1830: Li-ion (10 cells)

BCL1430: Li-ion (4 or 8 cells)

Weight 1.5 kg 1.6 kg

Model UC18YRL

Charging voltage 7.2 – 18 V

Charging time 3.0 Ah 45 min.

Weight 0.6 kg

1. When the battery power remaining runs out (The

battery voltage drops to about 12V (WH18DL,

WR18DL) / about 8V (WH14DL, WR14DL)), the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

SPECIFICATIONS

Cordless Impact Driver

Charge time is approximate. Actual charge time may

vary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WH14DL2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info