Bedienungsanleitung Hitachi WH14DY (Seite 9 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572130

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

English

〈UC18YG〉

Before using the power tool, charge the battery as follows.

1. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger.

2. Insert the battery into the charger

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger

(

See Fig. 4

)

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

The pilot lamp goes off to indicate that the battery is

fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power source

is too low.

(1) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

(2) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 3.

When the pilot lamp does not go off even if more

than 120 minutes have elapsed after starting of the

charging, stop the charging and contact your HITACHI

AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light up. At that time, cool the battery first,

then start charging.

3. Disconnect the charger power cord from the

receptacle

4. Hold the charger tight and pull out the battery

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by the

above precautions.

HOW TO USE

1. Installing the bit

Always follow the following procedure to install driver

bit. (Fig. 5)

(1) Pull the guide sleeve forward.

(2) Insert the bit into the hexagonal hole in the socket.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

2. Removing the bit

Please do the opposite point on the method of

installing bit.

3. Confirm that the battery is mounted correctly

4. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise (See Fig. 6) (The

and

marks are provided on the body).

5. Switch operation

CAUTION

⅜ Before using, confirm that the switch lever returns

to its original position when pulled and then

released. Failure of the switch lever to operate

properly can result in injury.

⅜ Do not hang the angle impact driver from a belt

and the like by the switch lever. The angle impact

driver may drop causing an accident. In addition,

this can also damage the switch lever.

⅜ When carrying the angle impact driver, confirm

that the lock button is in the OFF position. Carrying

the angle impact driver with the lock switch in the

ON position can cause the switch to inadvertently

be turned on resulting in injury.

⅜ Do not carry the angle impact driver by the switch

lever when carrying. This can cause a malfunction.

⅜ Be careful not to pinch your finger between the

switch lever and the angle impact driver. This can

cause an injury.

⅜ The switch is turned on when the switch lever is

pulled after having slid the lock button to the ON

position, and is turned off when the switch lever is

released. (See Fig. 7)

⅜ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

⅜ Always make sure to return the lock button to the

OFF position after using. (See Fig. 7)

NOTE

⅜ A buzzing noise is produced when the motor is about

to rotate. This is only a noise, not a machine failure.

01Eng_WH14DCAL_WE 08/8/27, 18:228

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WH14DY Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info