Bedienungsanleitung Hitachi WH18DBAL2 (Seite 12 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572118

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

(2) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 3.

Table 3 Charging time (At 20°C)

NOTE:

The charging time may vary according to temperature

and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE:

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2-3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

⅜ When the battery charger has been continuosly used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next

charging.

⅜ If the battery is recharged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

map light in green.

The battery will not be recharged. In such a case, let

the battery cool before charging.

⅜ When the pilot lamp flickers in red (at 0.2-second

intervals), check for and take out any foreign objects

in the charger’s battery installation hole. If there are

no foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it is at

all loose it could come off and cause an accident.

3. Installing the bit (WH14DBAL2 / WH18DBAL2)

Always follow the following procedure to install driver

bit. (Fig. 5)

(1) Pull the guide sleeve away from front of the tool.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

4. Selecting the socket matched to the bolt

(WR14DBAL2 / WR18DBAL2)

Be sure to use a socket which is matched to the bolt

to be tightened. Using an improper socket will not

only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex. or square-holed socket will

not give an adequate tightness for fitting to the nut or

anvil, consequently resulting in loss of tightening

torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

5. Installing a socket (WR14DBAL2 / WR18DBAL2)

Select the socket to be used.

ⅷ Pin, O-ring type

(1) Align the hole in the socket with the hole in the anvil

and insert the anvil into the socket.

(2) Insert the pin into the socket.

(3) Attach the ring to the groove on the socket.

ⅷ Plunger type (Fig.6)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push the

plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

ⅷ Retaining ring type

(1) Align the square portions of the socket and the anvil

with each other.

(2) Make sure to firmly install the socket by pushing it all

the way into the anvil.

(3) When removing the socket, pull it out of the anvil.

CAUTION:

⅜ Please use the designated attachments which are

listed in the operations manual and Hitachi’s catalog.

Accidents or injuries could result from not doing so.

Rechargeable batteries

Temperatures at which the

battery can be recharged

BSL1430, BSL1830

0°C – 50°C

BSL1440, BSL1840

Charger

UC18YRSL

Battery

BSL1430, BSL1830 Approx. 45 min.

BSL1440, BSL1840 Approx. 60 min.

01Eng_WH14DBAL2_WE 7/10/12, 16:1411

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WH18DBAL2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info