Bedienungsanleitung Hitachi WP14DSL (Seite 11 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572160

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

English

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

⅜ When the battery charger has been continuosly used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next

charging.

⅜ If the battery is recharged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

map light in green.

The battery will not be recharged. In such a case, let

the battery cool before charging.

⅜ When the pilot lamp flickers in red (at 0.2-second

intervals), check for and take out any foreign objects

in the charger’s battery installation hole. If there are

no foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it is at

all loose it could come off and cause an accident.

3. Installing the bit

Always follow the following procedure to install bit

piece and driver bit. (Fig. 5)

(1) Pull the guide sleeve away from front of the tool.

(2) Insert the bit piece and driver bit into the hexagonal

hole in the anvil.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

⅜ If the guide sleeve does not return to its original

position, then the bit is not installed properly.

⅜ This product also comes equipped with a bit piece.

Make sure that the bit piece is inside of the hexagonal

hole in the main shaft, then install the bit. (Fig. 6)

HOW TO USE

1. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise. (See Fig. 7) (The

and

marks

are provided on the body.)

CAUTION:

The push button cannot be switched while the oil

pulse driver is turning. To switch the push button,

stop the oil pulse driver, then set the push button.

2. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

3. Change rotation speed

As shown in Fig. 8, when the rotation switch-over

lever is slid to the lower side, the power mode (P) is

set. And when slid to upper side, the save mode (S) is

set.

Please use the save mode (S) when you want to lower

Maximum tightening torque.

CAUTION

In the work of the save mode (S), avoid the continuous

screw-tightening as temperature of electronic

components of the converter switch increases.

4. Tightening and loosening wood screws

Install the bit that matches the screw, line up the bit

in the grooves of the head of the screw, then tighten

it.

Push the oil pulse driver just enough to keep the bit

fitting the head of the screw.

CAUTION:

Applying the oil pulse driver for too long tightens the

screw too much and can break it.

Tightening a screw with the oil pulse driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted to

the screw.

Tighten with this oil pulse driver lined up straight

with the screw.

5. Number of screws tightenings possible

Please refer to the table below for the number of

screw tightened possible with one charge.

These values may vary slightly, according to

surrounding temperature and battery characteristics.

6. Using the hook

The hook is used to hang up the power tool to your

waist belt while working.

CAUTION:

⅜ When using the hook, hang up the power tool firmly

not to drop accidentally.

If the power tool is dropped, it may lead to an accident.

⅜ When carrying the power tool with hooked to your

waist belt, do not fit any bit to the tip of power tool. If

the sharp bit such as drill is fitted to the power tool

when carrying it with hooked to your waist belt, you

will be injured.

⅜ Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

(1) Removing the hook.

Remove the screws fixing the hook with Philips screw

driver. (Fig. 9)

(2)

Replacing the hook and tightening the screws.

Install securely the hook in the groove of power tool

and tighten the screws to fix the hook firmly. (Fig. 10)

Screw used

Battery

BSL1430

Wood screw ø4 x 50

Approx. 590

(Soft wood)

01Eng_WP14DSL_WE 9/24/09, 2:07 PM10

Hitachi WP14DSL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info