Bedienungsanleitung Hitachi WR12DAF3 (Seite 9 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572161

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

English

4. Extension bar: Code No. 873633

The extension bar is convenient for working in very

restricted spaces or when the socket provided cannot

reach the bolt to be tightened.

CAUTION

when the extension bar is used, the tightening torque

is reduced slightly compared with the ordinary socket.

5. Universal joint:Code No. 992610

The universal joint is convenient for impacting nuts

when there is an angle between the socket and

wrench, or when working in a very narrow space.

6. Duct Socket:

This is used for tightening bolts and nuts on flange

sections of air conditioners, type ducts, etc.

7. Corner attachment (Model EW-14R)

Use this attachment only when the machine is applied

to the nut or bolt at the right angle.

8. Bit adaptor: Code No. 991476

This is used for tightening small screws (M6 – M8).

NOTES

(1) This adaptor is set only on the anvil (drive angle) of

the main unit. The bit adapter cannot be attached to

the special accessory anvil (square drive).

(2) Before starting work with the adapter, tighten a few

screws with it to make sure it’s tightening with the

appropriate torque.

(3) Tightening speed will be greatly reduced when driving

wood, tapping or other similar screws.

Optional accessories are subject to change without notice.

APPLICATION

⅜ Tightening and loosening of all types of bolts and nuts,

used for securing structural items.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

〈

UC12SD

〉

Before using the impact wrench, charge the battery as

follows.

1. Insert the battery into the charger.

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger (See Fig. 3).

CAUTION

The UC12SD model is the exclusively designed

charger. This cannot charge batteries except the

specified batteries. It is possible to insert the batteries

other than the specified into the charger and it may

light up the pilot lamps. However, you are requested

to exercise utmost caution not to charge batteries

other than specified ones because these can not only

be charged but also such actions can result in the

malfuntion of chargers.

2. Connect the charger power cord to the receptacle.

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the power

cord from the receptacle and check the battery

mounting condition.

Code No.

Hexagonal width

across flats (mm)

993658 12

992613 13

992615 14

ⅷ Applicable plus driver bit

L 6.35

Bit No. L (mm) Code No.

No. 2

45 955229

70 955654

No. 3

45 955230

70 955655

Bit No.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WR12DAF3 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info