Bedienungsanleitung Hitachi WR18DSLH (Seite 12 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

572178

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

English

4. Inspecting the carbon brushes (Fig. 9)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with new ones when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely whthin

the brush holders.

NOTE:

When replacing the carbon brush with a new one, be

sure to use the Hitachi Carbon Brush Code No. 328481.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a slotted head screw driver, etc.,

as shown in Fig. 11.

When installing the carbon brush, choose the direction

so that the nail of the carbon brush agrees with the

contact portion outside the brush tube. Then push it

in with a finger as illustrated in Fig. 12. Lastly, install

the brush cap.

CAUTION:

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

6. Cleaning of the outside

When the impact wrench is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water. Do

not use chloric solvents, gasoline or paint thinner, as

they melt plastics.

7. Storage

Store the impact wrench in a place in which the

temperature is less than 40°C, and out of reach of

children.

NOTE:

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to be

charged when used, if stored for a long period.

8. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when

used with batteries other than these designated

by us, or when the battery is disassembled and

modified (such as disassembly and replacement

of cells or other internal parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE:

Due to HITACHI’s continuing program of reserch and

development, the specifications herein are subject to

change without prior notice..

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 105 dB (A)

Measured A-weighted sound pressure level: 94 dB (A)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Impact tightening of fasteners of the maximum capacity

of the tool:

Vibration emission value

ah = 12.0 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be

used for comparing one tool with another.

It may also be used in a preliminary assessment of

exposure.

WARNING

⅜ The vibration emission during actual use of the power

tool can differ from the declared total value depending

on the ways in which the tool is used.

⅜ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

01Eng_WR18DSHL_WE 12/14/10, 8:4112

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi WR18DSLH Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info