Bedienungsanleitung Hitec NEON_SS_FM (Seite 7 von 8) (Englisch)

30184

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

6 NEON T ransmitter Option Installation Directions.

Trainer

switch

Trainer

jack

Screws

ATV Board Installation

1. Open the case as instructed on page 3 and disconnect the throttle

s witch harness plug from the main board.

2. Disconnect the pow er from the radio b y removing the battery holder

or unplugging and removing the Nicad battery pack.

3. Remo v e the four scre ws holding in the large brown PC board in the

illustration.

4. Without unplugging anything on the board, you should be able to shift

the board up out of the wa y about 1 inch.

Note: slide the white wire ne xt to the antenna screw post out of the slot.

5. Pop the "cov er" out from the three small holes and place the ATV board

on the two screw posts. Secure the board with the two supplied screws , be sure to tighten the screws up snug.

6. Taking care to route the wires under the boards as much as possible , re-install the f our screws holding down

the large brown PC board.

7. Slide the white wire next to the antenna screw post into the slot and out of the wa y of the antenna as it is reinserted.

8. Re-install the battery.

9. Plug the throttle back in.

10. Taking care not to pinch any wires, slide the top of the case half's together then snap the bottom together .

Reinstall the antenna, antenna bezel, crystal and the lower case tabs.

11. All done? Range check y our radio and go fly!

Trainer P ort and Switch Installation

1. Open the case as instructed on page 3 and disconnect the throttle

s witch harness plug from the main board.

2. Disconnect the power from the radio by remo ving the battery holder

or unplugging and removing the Nicad battery pack.

3. Twist out and remov e the plastic cov er from the back side of the case

so the trainer plug can be accessed after the case is closed.

Clean up the edges with a hobby knif e .

4. Plug the 6 wire plug into the port marked "trainer" and route the

wires so they will not be pinched when the case is re-assembled.

5. Pop the plastic plug out from the top right of the Tx case and

install the switch b y removing both small nuts, sliding the s witch

up through the hole and securing both nuts so the top nut "jams"

the bottom one tight. Taking care to orient the switch so when the Tx is resting in your hand in the flying position,

the s witch is pulled tow ards you and snaps back a wa y from y ou when released.

6. Route the wires so they will not be pinched when the case is re-assembled.

7. Place the plug port PC board on the f our screw posts and use the f our screws to secure it.

8. Re-install the battery.

9. Plug the throttle back in.

10. Taking care not to pinch any wires, slide the top of the case half's together then snap the bottom together .

Reinstall the antenna, antenna bezel, crystal and the lower case tabs.

11. All done? Range chec k your radio and go fly!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitec NEON_SS_FM Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info