558736

Home Easy HE-414 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
RE-INVENTING THE HOME
HOME
easy
HE-414
Remote Control Outdoor
V1.0
OFF: An additional safety feature of the HE410 is the ability to switch off the
power as per a normal socket.
INSTALLATION WARNING:
ON INSTALLATION TURN OFF YOUR
MAINS ELECTRIC SUPPLY
This product should be fitted by a competent
person in accordance with the instructions listed
below and with the relavent clauses of the IEE
wiring regulations BS7671.
The outdoor socket should be used in
conjunction with a fused spur connection, all
connections to the socket need to be made as
instructed, making sure that the cable used is
appropriate for the installation environment, free
from stress & terminals are tightened fully.
1. Open up the front, flip top cover.
2. Unscrew the four screws shown. To
separate the front, from the back of the
unit.
3. After all 4 screws have
been removed; the front will
separate from the back.
Front half
Back half
Opening Unit:
2. Using the back half of the unit as a template, pencil mark all four
corners onto your chosen surface. Making sure 'TOP' (marked on
the casing is at the top.
3. Drill all four marked holes and insert suitable wall plugs for a
number ‘8’ screw (recommended size).
4. Screw to the wall.
Fixing Holes
Mounting Socket:
1: In the back half of the unit, in all four corners are purpose made holes for fixing your
remote socket to your intended surface. The outdoor socket needs to be mounted
onto a flat, vertical surface. Free from grease, loose material and any corrosive
substances. We recommend a house or sturdy garden wall.
Remove Bottom
'Entry Blank'
Wiring Remote Socket:
On the back half of the remote socket you will see that there are 4 circular shaped
disks (‘Entry blanks’) on each side (3 are plastic, 1 is rubber). Depending on if you wish
to link up more than one ‘Outdoor remote socket’ you can remove or replace these
disks.
It is recommended that the bottom most 'Entry blank' should be removed to gain entry
into the 'Outdoor Remote Socket'. This will help keep the moisture out.
If installing the Outdoor socket with conduit from the sides or top attachment, a 5mm
hole must be drilled through the bottom left drainage hole. This will allow for any
condensation forming in the conduit, to drain out.
Caution: opening the drainage hole will affect the IP rating of the product. Ensure that
jetted water is not directly sprayed onto the unit.
Do Not drill out the drainage hole when installing the
Outdoor socket into a dusty environment. Always install
the unit via the bottom cable entry, making sure that a
5mm hole is drilled into the lowest point in the conduit
system.
1. Switch off and isolate the mains power before altering
the code setting
4. Send the cable through the conduit
and into the ‘Outdoor Remote Socket’.
(Live - Brown)
(Earth - Green & Yellow)
(Neutral - Blue)
Exposed wire
(L = Live - Brown)
(E = Earth - Green & Yellow)
(N = Neutral - Blue)
LEN
(FIG.8)
LEN
Please Note: The Cable is
up inside the box, so that
no wires can be seen.
2.
2: Cut back the cable to reveal 3 separate wires
L= Live  Brown
E= Earth  Green & Yellow
N= Neutral  Blue
3. Now strip each wire, exposing 10mm of its
3: Insert the exposed core wires into their related
terminals and clamp down by tightening the
respective screw.
L= Live  Brown
E= Earth  Green & Yellow
N= Neutral  Blue
When installing secondary Outdoor receiver sockets always place them
the units approximately 30-40cm apart.
Installation:
1. Fist select your required location, it's recommended that the PIR is installed
approximately 3 metres off the ground (ideally under the eaves of the building) and,
away form direct sources of sunlight and heat.
Warning: Avoid installing the Remote Control PIR onto metallic surfaces
and above heating vents as this will affect the operating performance.
Avoid Direct Heat
Sources
Detection Distance
The HE-414 allows you to control your HomeEasy outdoor
socket via a wire free remote control PIR sensor. When the
PIR beam is broken the outdoor PIR will switch on your
Remote control sockets for between 15 seconds and
4 Minutes.
AUTO: Allows the Remote Control PIR to switch
on/off the outdoor socket.
ON: Sets the Outdoor socket as a standard outdoor socket.
USE THIS OPTION WHEN USING GARDEN
MACHINERY SUCH AS A LAWNMOWER OR HEDGE CUTTERS.
-Selectable timer setting
-10Metre Detection Range
-IP44 Weather Proof
-25 Metre Wire Free Range
-Battery Powered 3*AAA
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Home Easy HE-414 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info