Bedienungsanleitung Home Easy HE-440 (Seite 1 von 2) (Englisch)

558739

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

RE-INVENTING THE HOME

HOME

easy

HE-440 Outdoor Remote

Control 4Gang Kit

V1.0

OFF: An additional safety feature of the HE440 is the ability to switch off the

power as per a normal socket.

Unused accessory Channels should be set to OFF

INSTALLATION WARNING:

ON INSTALLATION TURN OFF YOUR MAINS ELECTRIC SUPPLY

This product should be fitted by a competent person in accordance with the

instructions listed below and with the relevant clauses of the IEE wiring regulations

BS7671.

For fixed installation only

1. Remove the front cover by

unscrewing the front cover.

Installation Guide:

Wiring Remote Socket:

On the outdoor enclosure you will see that there are a number of rubber entry spaces

(‘Entry blanks’) on each side, depending on location and wiring setup a number of

these can be removed.

If installing the HE440 with conduit from the sides or top attachment, a 5mm hole

must be drilled through the bottom left drainage hole. This will allow for any

condensation forming in the conduit, to drain out.

Caution: opening the drainage hole will affect the IP rating of the product. Ensure that

jetted water is not directly sprayed onto the unit.

Do Not drill out the drainage hole when installing the Outdoor socket into a dusty

environment. Always install the unit via the bottom cable entry, making sure that a 5mm

hole is drilled into the lowest point in the conduit system.

The HE-440 allows you to control up to 4

separate outdoor electrical products

independently using the HomeEasy

remote control timer, with a maximum

combined load of 3000W.

AUTO: Allows the Remote Control to switch on/off

the HE440. See Pairing/Deleting with Remote

ON: Sets the Outdoor socket as a standard outdoor socket.

USE THIS OPTION WHEN USING GARDEN

MACHINERY SUCH AS A LAWNMOWER OR HEDGE CUTTERS.

-Selectable timer setting

-12 Programmable memory Settings

-Security Mode Setting

-Single and Daily Timer Functions

easy

HOME

The HE440 should be used in conjunction with a fused spur connection, all connections

to the socket need to be made as instructed, making sure that the cable used is

appropriate for the installation environment, free from stress & terminals are tightened

fully.

-Single and Daily Timer Functions

-IP56 Weather Proof

-30 Metre Wire Free Range

-CR2032/23A Battery (Included)

Product Specification:

4 Gang Remote Control Receiver: HE-440

Input: 230V - 240V ~50Hz

Range: 30 Metres (Open Distance)

Frequency: 433.92MHz

Max Load: 3000W

(Combined Resistive load)

IP56 (Lid Closed)

Warning: Never Exceed the Product Specification

Remote Control PIR: HE-403

Battery: 23A & CR2032 (Included)

Range: 30Metres (Open Distance)

Frequency: 433.92MHz

Indoor use only

3. Using the back half of the unit as a template, mark

all four corners onto your chosen surface. Insert

suitable wall plugs and secure to the wall using

number '8' screw (recommended size).

2: In the back half of the unit, in all four corners are

purpose made holes for fixing your HE440 to your

intended surface. The HE440 needs to be mounted

onto a flat, vertical surface, free from grease, loose

material and any corrosive substances. We

recommend a house or sturdy garden wall.

Recommended Setup:

Voltage In:

230-240V ~ 50Hz

Channel 3 Out

Channel 1 Out

Channel 2 Out

Channel 4 Out

Once removed the entry blanks

are removed, appropriate cable

glands need to be installed (not

included).

Input Power: (See Wiring Diagram)

1: Switch off and isolate the mains power before Installing or altering the

electrocal connections and remove the terminal covers.

2: Send the cable through the gland and into the HE440.

3: Cut back the cable to reveal the 3 separate wires

  L= Live  Brown

  E= Earth  Green & Yellow

  N= Neutral  Blue

4: Now strip each wire, exposing 10mm of its core

5: Insert the exposed core wires into their related terminals

and clamp down by tightening the respective screw. replace

the terminal covers and tighten the cabel glands, making

sure wall wires are secure.

Wiring Diagram:

Accessory Output 1 Accessory Output 2 Accessory Output 3

Accessory Output 4

Input Power

230 - 240V ~50HZ

 

= Live   Brown

= Earth   Green & Yellow

= Neutral   Blue

The HE-200 Remote Control Timer can be paired with 16 separate

receiver units, to select the required unit code, press the unit

button unitl the required number is displayed.

Each unit code will indavidually can indavidually operate single

channel or all 4 channesl.

The HE-200 comes with a preset to Group code A. When

using additional remote control timers you will need to

select a new group code.

To select a new group code, remove the battery cover and

using a small screw driver, rotate the group dial to a new

setting e.g. Group B

HE440

HE200

WARNING:

You MUST install an earth cable between the origin of the installation and the earth

terminal of the outdoor socket. This must be insulated inside a sleeve protector within

the conduit.

If using metal conduit, earth continuity must be maintained between conduits. Seal

Conduit and conduit entry with a non setting conduit sealant. Purchasable form you

local electrical retailer.

Operating Mode:

Output:

230-240V ~ 50Hz

3000W Combined

6. Reconnect the mains power, the HE440 is now ready programming

(See Pairing/Deleting with Remote).

Replace the front cover and tighten the screws.

Each Acessory Output Channel can operate in 3 seperate modes, use the slide

switch on each channel to select the mode setting.

Home Easy HE-440 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info