Bedienungsanleitung Hotpoint SIDC30BA1 (Seite 8 von 16) (Englisch)

665364

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Ifa13ampplug(BS1363)isused itmustbetted

with a 13 amp fuse, either in the plug or adaptor or at

the distribution board.

If you are in any doubt regarding the electrical supply

toyourmachine,consultaqualiedelectricianbefore

use.

How to connect an alternative plug

The wires in this mains lead are coloured in accordan-

ce with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Fuse

Blue

Brown

Cord

The power supply cable must never be bent

or dangerously compressed.

The power supply cable must only be repla-

ced by an authorised serviceman.

BEFORE USE

Beforeusingtheapplianceforthersttime,remove

all stickers, protective plastic or cardboard case from

the soleplate of the iron.

Make sure that all adhesive parts have been

removed from the soleplate with a dampened soft

cloth and eliminate any residues or particles from

the manufacturing process, by repeatedly lling and

emptying the water reservoir.

When switching on the iron for the rst

time, you may notice an unpleasant odour, a

little smoke and some impurities that will

disappear in a few minutes. When using the steam

function for the rst time, do not direct the steam

jet on the garments because of the possible

presence of manufacturing residues in the steam

dispenser.

Filling the water reservoir (A)

We recommend using demineralised water.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA appro-

ved fuse to BS 1362 should always be used, and the

fusecoverre-tted.Ifthefusecoverislost,theplug

must not be used until a replacement is obtained.

Replacement fuse covers

Ifareplacementfusecoveristted,itmustbeofthe

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable throu-

gh partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 ampere rewi-

reable plug bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in complian-

ce with BS 5733) which is accessible without

moving the appliance.

Disposing of the plug

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be acciden-

tally inserted into a socket.

Instructions for connecting cable to an

alternative plug

The wires in the mains lead are coloured in

accordance with the following code:

GREEN & YELLOW EARTH

BLUE NEUTRAL

BROWN LIVE

As the colours of the wires in the lead may not corre-

spond with the coloured markings identifying the ter-

minals in your plug, proceed as follows:

• Connect Green & Yellow wire to terminal marked

E or

or coloured Green or Green & Yellow.

• Connect Brown wire to terminal marked L or co-

loured Red.

• Connect Blue wire to terminal marked N or co-

loured Black.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint SIDC30BA1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info