Bedienungsanleitung Homedics PAR-100 (Seite 4 von 5) (Englisch)

518415

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

How to set up the paraffin bath

1. Remove all contents from packaging and check to make sure

you have all of the following components of the ParaSpa Mini

paraffin bath:

• Paraffin bath tub

• Plastic lid

• Plastic grate

• Three 500g bags of Paraffin Wax

• 30 plastic liners

2. Place unit on a level and sturdy table or surface and remove

the lid.

3. Make sure Paraffin Wax System tub is empty before putting

wax into tub.

4. Open the bags of Paraffin Wax and place wax in the tub.

Open only as many bags as you plan to use. The unit is

designed to hold a maximum of 1.6 kg of paraffin wax and a

minimum of 1 kg. See Fig.1 Always keep the level of paraffin

wax filled to the “MIN” level marked on the inside of the tub.

5. Plug the unit into a 230V AC power supply. The green LED

light indicates when the unit is plugged in. The red light will

turn on and off as the heating element works.

NOTE: Unit is automatically turned “on” when it is plugged in.

If not used in 48 to 72 hours, turn dial down to “SOLID”.

If not used for weeks at a time unplug unit and store in a

cool, dry place.

6. Turn the dial to “MELT” to melt the paraffin wax. See Fig.2

The paraffin wax should melt in less than 12 hours, usually in

under 4-5 hours. The red LED light indicates that the heater

element is operating. Place the lid onto the top of the unit.

7. Turn the dial to “WARM” after paraffin wax is completely

melted. Remove the lid and place the grate into the wax and

allow it to sink to the bottom of the tub. See Fig.3 Place the

lid back onto the top of the unit. Wait about 1 hour for the

paraffin wax to cool down to an ideal temperature before

using. The Paraffin Wax System unit is designed to be used

at room temperature. If the wax starts to solidify or flakes

form on the top surface, turn dial clockwise(right) to increase

the temperature.

NOTE: The room temperature can have an effect on the unit’s

performance. Therefore we always recommend testing the

paraffin temperature on the inside of the wrist area before

dipping your entire hand or elbow.

NOTE: NEVER dip your hand, foot or elbow into the paraffin

bath while the unit is in “MELT” mode!

NOTE: Place the grate into the unit only when the paraffin wax

is melted.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

How to use the paraffin treatment:

1. Before immersing your hand or elbow test the paraffin wax on the inside of your wrist to make

sure the temperature of the wax is comfortable. Remove all jewellery before dipping (i.e. rings,

bracelets, watch).

NOTE: It is suggested you wash the area to be treated and apply lanolin-based hand lotion

over the area before dipping it into the paraffin wax. This will allow the wax to be removed

easier and will help moisturize the skin.

2. Dip your hand or elbow into the melted paraffin wax and remove immediately. Wait a few

seconds until the wax solidifies. Try to avoid moving your hand or elbow while wax is applied.

NOTE: Dipping process is quick. Do not leave hand or elbow in the tub. Do not soak.

Dip quickly in and out.

3. Repeat this step several times until several layers have formed, 6-10 coatings are suggested.

If paraffin wax temperature is too hot or too cold, adjust the temperature accordingly. Turn the

dial clockwise (right) to increase the paraffin wax temperature or anti-clockwise (left) to reduce

the paraffin wax temperature.

4. For longer heat treatment, place a plastic liner (provided) over the treated area and twist bag

at opening. Keep paraffin wax and liner on treated area for 10-20 minutes for ultimate therapy.

See Fig.4

NOTE: When using the paraffin bath with plastic liners on your feet, do not walk around!

This may cause you to slip and fall.

5. Peel off the wax from the treated area. If using a plastic liner, peel the plastic lining from the

area being treated. Paraffin wax will peel off with liner. See Fig.5

6. Discard used wax.

NOTE: If you are the only person using the ParaSpa Mini, the wax can be re-used, simply put

it back into the tub to re-melt.

MAINTENANCE:

Periodically, the used portion of paraffin wax should be replaced and the unit should be cleaned.

1. Unplug unit and remove grate. Allow paraffin wax to solidify overnight.

2. Push on one end of paraffin wax block. This will tip it up. Lift the block out of the unit and

dispose of it. DO NOT USE SHARP OBJECTS TO REMOVE THE PARAFFIN WAX BLOCK,

THIS MAY SCRATCH OR DAMAGE THE TUB. If the paraffin wax does not remove easily, plug

unit in and allow to heat for 10–15 minutes then remove the paraffin wax block and unplug the

unit.

3. Wipe the inside of the unit with a disposable towel to remove residual dirt and paraffin.

4. With a damp, soapy cloth, wipe clean. DO NOT POUR WATER INTO THE UNIT, OR IMMERSE

THE UNIT IN WATER.

5. Store in a cool, dry place. When you are ready to re-use the Paraffin Wax System paraffin bath

for the next heat treatment, repeat steps 2-7, “How to set up the paraffin bath unit”. Then,

follow steps 1-6, “How to use the paraffin treatment”.

Plug (MODEL PAR-100-0GB ONLY)

If the plug on this appliance is damaged, it can be replaced with a

BS 1363 plug, fitted with a 3A BS 1362 fuse. Only use a 3amp fuse

with this appliance. Care must be taken when changing the plug.

If in doubt, contact a qualified electrician.

Homedics PAR-100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info