Bedienungsanleitung Homelite UT46510 (Seite 13 von 40) (Englisch, Französisch, Spanisch)

630639

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Page 9 — English

ASSEMBLY

INSTALLING THE FRONT HANDLE

See Figure 4.

 Position the front handle as shown.

 Depress the buttons on the handle and insert into the

frame. Press down on the handle until the button on the

handle clicks into place.

ASSEMBLING THE WHEEL/DRAG STAKE

ASSEMBLY

See Figure 5.

 Locate the axles, hitch pins, washers and wheels.

 Slide the wheel onto the axle.

 Place a washer on the outside of the wheel and slide to

rest against the wheel.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel/drag stake assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.

 Repeat with the second wheel.

INSTALLING THE WHEEL /DRAG STAKE

ASSEMBLY

See Figure 6.

Use the wheel/drag stake assembly to transport the unit to

and from the work area or when cultivating.

To install:

 Remove the adjustment knob located at the back of the

tine shield.

 Insert the wheel/drag stake assembly into the bracket at

the back of the tine shield. To place the wheels in a high

position, insert the knob in the first hole. For a lower wheel

position, insert the knob in the second or third hole.

 Insert adjustment knob through holes in bracket, pass-

ing through desired hole in wheel/drag stake assembly,

to secure wheel/drag stake assembly at desired height.

 Thread the adjustment knob into the nut and tighten, to

secure wheel/drag stake assembly.

INSTALLING THE TINES

See Figure 7.

The cultivator has four tines —two inner tines stamped B

and C, and two outer tines stamped A and D. For correct

operation of the unit, the tines must be installed in the cor-

rect orientation.

NOTE: The view of the gearbox for tine installation is from

the front of the cultivator.

 Lean the unit back on its wheels so that the handlebar

rests on the ground.

 Place tine C on the tine shaft to the left of the gear box.

The stamped side of the tine should face away from the

gear box.

 Place tine B on the tine shaft to the right of the gear box.

The stamped side of the tine should face away from the

gear box.

 Place a felt washer on each side of the tine shaft, and

slide to rest against the inner tines.

 Place the outer tine stamped D on the left side of the tine

shaft. The stamped side should face in toward tine C.

 Place the outer tine stamped A on the right side of the

tine shaft. The stamped side should face in toward

tine B.

NOTE: When installed correctly, the angled edge of the

tine blades should face the ground.

 To secure the tines to the tine shaft, insert the hitch pin

into the holes located on either side of the tine shaft.

NOTE: The unit will not operate properly if the tines are

installed incorrectly. If you notice a problem with the cultivat-

ing operation of the unit, check for proper tine positioning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Homelite UT46510 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Homelite UT46510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info