Bedienungsanleitung HomeMatic HmIP-VDMOT (Seite 2 von 2) (Deutsch, Englisch)

808550

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Installation and Operating Manual

Homematic IP Valve Drive – motorised

HmIP-VDMOT

Printed in Hong Kong. Subject to modiﬁcations.

153305 // V1.0 (08/2018)

1. Package contents

Homematic IP Valve Drive – motorised

Valve adapter VA 80 (thread size M30 x 1.5 mm)

User manual

2. Information about this manual

Read this manual carefully before starting to use the device. Keep the manual

so you can refer to it at a later date if you need to. If you hand over the device

to other persons for use, please hand over this manual as well.

Symbols used:

Attention! This indicates a hazard.

Please note: This section contains important additional information.

3. Hazard information

Do not open the device. It does not contain any parts that can be

maintained by the user. If you have any doubts, have the device checked

by an expert.

For safety and licensing reasons (CE), unauthorized change and/or

modiﬁcation of the device is not permitted.

The device may only be operated in dry and dust-free environment and

must be protected from the eects of moisture, vibrations, solar or other

methods of heat radiation, cold and mechanical loads.

The device is not a toy; do not allow children to play with it. Do not leave

packaging material lying around. Plastic ﬁlms/bags, pieces of polystyrene,

etc. can be dangerous in the hands of a child.

We do not assume any liability for damage to property or personal injury

caused by improper use or the failure to observe the hazard information.

In such cases, any claim under warranty is extinguished! For consequen-

tial damages, we assume no liability!

The device may only be used for ﬁxed installations. The device must be

securely attached within a ﬁxed installation.

In case of visible damage of the existing radiator/valve drive, valve or

heating pipes, please contact a specialist.

The device may only be operated within residential buildings.

Using the device for any purpose other than that described in this

operating manual does not fall within the scope of intended use and shall

invalidate any warranty or liability.

4. Function

With the Homematic IP Valve Drive – motorised you can control the valve po-

sition and thus regulate the water ﬂow rate to regulate the room temperature.

The valve has to be operated in connection with a Homematic IP Floor Heat-

ing Actuator – 12 channels, motorised (HmIP-FALMOT-C12).

5. Installation

The valve drive can be installed in any position (e.g. upside down).

For installation, no tools are required.

To install the valve drive, proceed as follows:

• Make sure if the valve drive ﬁts to the thread size M30 x 1.5mm. We rec-

ommend to use the valve template available for download in the download

area of www.eQ-3.com. If the valve drive diers, you will need a corre-

sponding adapter.

• Attach the supplied valve adapter (VA 80) to the valve.

• Attach the valve drive to the adapter. Make sure that the valve drive engages

properly.

To disassemble the device press the catch and remove the valve drive

from the adapter.

6. Connection to the ﬂoor heating actuator

For the regulation of the room temperature, the valve drive must be con-

nected directly to the Homematic IP Floor Heating Actuator – 12 channels,

motorised (HmIP-FALMOT-C12). To do this, please proceed as follows:

• Connect the connecting cable of the valve drive to the clamp terminals of

the ﬂoor heating actuator.

7. Maintenance and cleaning

The product does not require any maintenance. Enlist the help of an

expert to carry out any repairs.

Clean the device using a soft, lint-free cloth that is clean and dry. Do not use

any detergents containing solvents, as they could corrode the plastic housing

and label.

8. Technical speciﬁcations

Device short name: HmIP-VDMOT

Supply voltage: 3.3 VDC, SELV

Current consumption: 120 mA max.

Degree of protection: IP20

Protection class: III

Ambient temperature: 0 to 50 °C

Method of operation: Type 1

Connection: M30 x 1.5 mm

Pollution degree: 2

Linear travel: 4.3 ±0.3 mm

Dimensions: 44 x 54 x 50 mm (without connecting cable)

Weight: 80 g

Subject to technical changes.

The CE sign is a free trading sign addressed exclusively to the

authorities and does not include any warranty of any properties.

Instructions for disposal

Do not dispose of the device with regular domestic waste! Electronic

equipment must be disposed of at local collection points for waste

electronic equipment in compliance with the Waste Electrical and

Electronic Equipment Directive.

Bevollmächtigter des Herstellers:

Manufacturer’s authorised representative:

eQ-3 AG

Maiburger Straße 29

26789 Leer / GERMANY

www.eQ-3.de

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HomeMatic HmIP-VDMOT Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HomeMatic HmIP-VDMOT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info