800566

HomeTech QT6287 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
QT6287 EN
7
8.5 Collection bag
Note: Before you remove and empty the collection bag ensure that the tool has
been disconnected from the mains power supply.
To empty the collection bag simply open the zip fastener, empty the bag and then close the
zip fastener again
When the collection bag is open you can also check the function of the blow/vac’s slide
control. If there is a blockage in the tool, check this function and remove the blockage.
9 CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the power plug.
9.1 Cleaning
Keep the ventilation slots of the tool clean to prevent overheating of the engine.
Regularly clean the tool housing with a soft cloth, preferably after each use.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
9.2 Maintenance
Our tools have been designed to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon proper tool care and regular
cleaning.
10 TECHNICAL DETAILS
Rated voltage
230-240V
Rated frequency
50Hz
Rated power
2800W
Rotation speed
10000-15000min
Cable length
0.35m
Protection class
II
Protection degree
IPX0
Collect bag volume
35L
Shredding ration
10:1
Max air speed
270km/h
Max air volume
13.2m³/min
Electric motor type
Brushed
Second handle type
auxiliary handle
Quick release collect bag
Yes
Double wheel support
Yes
Motor winding material
aluminium
Functions
Shredding, blowing, vacuuming
QT6287 EN
6
7 ASSEMBLY
Your new blow/vac requires very little assembly work before it is ready for use.
Warning: if any part is missing or damaged, do not plug in the machine until
you have replaced the missing or damaged part.
7.1 Assembling the tubes (Fig. 1, 2)
1. Slide the top tube section into the motor housing, then tighten the screws on both sides
and make sure the tube is firmly fixed to the motor housing.
2. Insert the bottom section tube into the top section tube and push them until they are
connected firmly together. Finally tighten the screws on both sides.
3. Attach the wheels with rake to the bottom section tube.
7.2 Shoulder belt
Attach the shoulder belt to the foreseen hook on the handle. To adjust the shoulder belt to
the required length, simply slide the adjustable strap buckle forward or backwards.
7.3 Collection bag (Fig. 3)
Before fitting the collection bag ensure that the blow - vacuum function selector lever
operates smoothly and that it is not obstructed by debris from the previous use.
Secure the hook of the collection bag to the tube and then install the entrance of debris of
the collection bag in the foreseen opening.
8 OPERATION
8.1 Steps prior to operation
Only operate the device after completely assembling it. Prior to each use, check the power
cord for signs of damage. Under no circumstances should the power cord be used if it shows
any signs of damage.
Ensure that the blow/vac is only connected to conventional sockets with a 230 V alternating
current supply.
8.2 Switching ON/OFF (Fig. 4)
Press the On/Off switch to start machine.
To stop the machine simply let go of the On / Off switch.
8.3 Use/Operation
The easiest way to use the blow/vac is to place the shoulder belt in a comfortable position
over your shoulder and hold the rear handle at hip height so that the majority of the tool’s
weight rests on the rollers.
When using the blow/vac to pick up leaves it is best to move the tool on its rollers. This
ensures that the blow/vac is at the perfect height above the ground. The blow/vac is
designed only to pick up leaves. To avoid damage to the tool that is not covered by the
warranty, do not use it to pick up branches, stones or other hard materials.
When using the tool as a leaf blower always work away from solid objects such as walls,
fences, etc. Whilst you work do not place the blow/vac tube too close to the leaves. The
tool will be more effective if you keep it at a certain distance away from the leaves and
blow the leaves forwards.
8.4 Switching operating mode (Fig. 5)
To switch the tool from blower mode to vacuum mode, simply switch it off at the main
switch and move the blow - vacuum function selector lever to the desired position.
… 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HomeTech QT6287 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info