Bedienungsanleitung Honda CR-V - 2015 (Seite 73 von 81) (Englisch)

617794

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

138 | | 139

MAINTENANCEMAINTENANCE

TABLE OF CONTENTS

INDEX

VISUAL INDEX

VOICE COMMAND

INDEX

SAFETY

INFORMATION

CUSTOMER

INFORMATION

INSTRUMENT PANEL

SPECIFICATIONS

VEHICLE

CONTROLS

MAINTENANCE

AUDIO AND

CONNECTIVITY

HANDLING THE

UNEXPECTED

BLUETOOTH®

HANDSFREELINK®

DRIVING

HONDALINK®

NAVIGATION

Tire Pressure Monitoring System ( TPMS) - Required Federal

Explanation

U.S. models only

Each tire, including the spare (if provided), should be checked monthly

when cold and inﬂ ated to the inﬂ ation pressure recommended by the

vehicle manufacturer on the vehicle placard or tire inﬂ ation pressure label.

(If your vehicle has tires of a different size than the size indicated on the

vehicle placard or tire inﬂ ation pressure label, you should determine the

proper tire inﬂ ation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with

a tire pressure monitoring system (TPMS) that illuminates a low

tire pressure telltale when one or more of your tires is signiﬁ cantly

under-inﬂ ated.

Accordingly, when the low tire pressure telltale illuminates, you should stop

and check your tires as soon as possible, and inﬂ ate them to the proper

pressure.

Driving on a signiﬁ cantly under-inﬂ ated tire causes the tire to overheat and

can lead to tire failure. Under-inﬂ ation also reduces fuel efﬁ ciency and tire

tread life, and may affect the vehicle’s handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance,

and it is the driver’s responsibility to maintain correct tire pressure, even if

under-inﬂ ation has not reached the level to trigger illumination of the TPMS

low tire pressure telltale.

Your vehicle has also been equipped with a TPMS malfunction indicator to

indicate when the system is not operating properly. The TPMS malfunction

indicator is combined with the low tire pressure telltale. When the system

detects a malfunction, the telltale will ﬂ ash for approximately one minute

and then remain continuously illuminated. This sequence will continue upon

subsequent vehicle start-ups as long as the malfunction exists.

When the malfunction indicator is illuminated, the system may not be able

to detect or signal low tire pressure as intended.

TPMS malfunctions may occur for a variety of reasons, including the

installation of replacement or alternate tires or wheels on the vehicle that

prevent the TPMS from functioning properly.

Always check the TPMS malfunction telltale after replacing one or more

tires or wheels on your vehicle to ensure that the replacement or alternate

tires and wheels allow the TPMS to continue to function properly.

Testing of Readiness Codes

Your vehicle has “readiness codes” as part of the onboard self-diagnostic system.

Some states refer to these codes as a test to see if your vehicle’s emissions

components are working properly. The codes may not be read if you go through the

testing just after the battery has gone dead or been disconnected.

To check if they are set, turn the vehicle on without starting the engine. The

malfunction indicator lamp will come on for several seconds. If it goes off, the

readiness codes are set. If it blinks ﬁ ve times, the readiness codes are not set.

If you are required to have your vehicle tested before the readiness codes are set,

prepare the vehicle for retesting by doing the following:

1. Fill the gas tank to approximately 3/4 full.

2. Park the vehicle and leave the engine off for 6 hours or more.

3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).

4. Start the engine without touching the accelerator pedal, and let it idle for 20

seconds.

5. Keep the vehicle in Park (P). Increase the engine speed to 2,000 rpm, and hold it

there for about 3 minutes.

6. Let the engine idle with your foot off the accelerator for 20 seconds.

7. Select a nearby, lightly traveled major highway where you can maintain a speed

of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway with

the vehicle in Drive. Do not use cruise control. When trafﬁ c allows, drive for 90

seconds without using the accelerator pedal. (Vehicle speed may vary slightly;

this is OK.) If you cannot do this for a continuous 90 seconds because of trafﬁ c

conditions, drive for at least 30 seconds, then repeat two more times (for a total of

90 seconds).

8. Drive in city/suburban trafﬁ c for at least 10 minutes. When trafﬁ c conditions

allow, let the vehicle coast for several seconds without using the accelerator

pedal or the brake pedal.

9. Park the vehicle and leave the engine off for 30 minutes.

The readiness codes are erased when the battery is disconnected, and set again

only after several days of driving under a variety of conditions.

If a testing facility determines that the readiness codes are not set, you may be

requested to return at a later date to complete the test, or see your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda CR-V - 2015 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda CR-V - 2015

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info