Bedienungsanleitung Honda Honda Engines GV400 (Seite 4 von 5) (Englisch)

13089

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

First 20 operating Hrs.

Every 20 operating Hrs.

Every 100 operating Hrs.

. CHANGE ENGINE OIL

. CLEAN AIR CLEANER

. CHANGE ENGINE OIL

l CLEAN SPARK PLUG AND CHECK GAP

.C(LJ$Jji@

Breaker type CD1 type

0.6 - 0.7 mm

0.9 - 1.0 mm

\/--

(0.024 - 0.027 in) (0.035 - 0.039 in)

* For replacement,

use BMdA or

l BPMdA or BPMRdA

Qr==-- @

BMRdA spark

(NGK)

@=-- @

plug WW

* Engine oil capacity: 1.2 1 (2.54 US pt, 2.1 I Imp

Pt)

* Use SE rated SAE lOW40 engine oil.

* Remove the drain plug and raise the carburetor

side UP to drain all of the oil.

* Remove dust from paper element A by applying compressed air or taPPing

the case lightly. If the paper element is excessively dirty, replace or wash it

in liquid detergent and water and flush until water is clear. Dry it t.houghlY

l CHECK FUEL LINE

by applying compressed air before installing.

t Check the fuel line for cracks or

t Wash the foam element B in liquid detergent and water and flush until water

is clear. Dry it throughly by applying compressed air. After drying, soak in

leaks and replace it if necessary.

oil and squeeze out the excess.

w a9

ADJUSTMENT

. ADJUST VALVE CLEARANCE

LINDER HEAD GASKET

‘MARK”

The following adjustments should be performed by your HONDA general

purpose engine dealer.

l ADJUST IGNITION TIMING (Breaker type)

. ADJUST CARBURETOR SCREW

* Adjust contact breaker points so that they just

start to open when F mark on flywheeel aligns

with the mark on cylinder barrel.

* IGNITION TIMING: 20” BTDC (fixed)

lE@xxE lz2ximmED .@nm%l0M@

* Drain gasoline from fuel tank and carburetor,

and change the engine oil.

WARNING: Use caution; gasoline is flammable.

* Disconnect the battery.

* Store in a dust-free, dry area on a level surface.

* Pull the starter rope until resistance is felt to

T BREAKER ASSY

prevent dust from coming into engine’. (JB type only)

FLOAT VALVE

WOROM@ DllA@RAM

* Idle Speed

* Measure at TDC on compression when engine is

(1) Start the engine and run at idle until a normal

cold.

operating temperature is obtained.

(2) Turn the throttle stop screw in or out as necessary

* STANDARD:

until the specified idle speed is obtained.

Specified idle speed: 1,700 rpm

IN 0.06 - 0.12 mm (.002 - .OOS in)

* Pilot Screw

EX 0.0 9- 0.15 mm (.004 - .006 in)

If the pilot screw setting needs adjustment:

(1) Turn pilot screw in or out until the highest idle

* .If the clearance is less than the standard limit,

rpm is reached.

grind valve stem or replace valve.

* The CD1 type does not require adjustment.

(2) Readjust to the specified idle speed using the

throttle stop screw.

OM8UAL~uo~)M 1

BATTERY * Use a battery rated at 12V-32AH or more.

* Use only automobile type vinyl covered wire

FOR BATTERY

(for low voltage) whose effective diameter is

CHARGING

* A throttle control cable may be used in

any one of the two pull directions shown.

more than 4.4mm (0.172 in) and which utilizes

FOR LAMP

press fit terminals between the battery and the

LIGHTS-TOTAL RAT-

engine. Length must be within lm (3 ft).

ING: 60W (MINIMUM)

* Protect the terminals with grease and completely

BATTERY

- 1OOW (MAXIMUM)

cover the positive terminal with a rubber cap.

When connecting terminals, ensure positive and

* Do not interconnect AC light circuit and bat-

negative leads are correctly connected.

tery circuit as alternator and wiring will be

ImaffKAwj

Cycle, valve arrangement

Displacement

Max. output

Max. torque

Fuel consumption

Dry weight

cm3 (cu in)

Wrpm

kg-cm (ft-lb)

d-JJ’ h (lb/~ h)

kg (lb)

*JE type

4Stroke, side valve

406 (28.1)

11.0/3,600

245 (18)

270 (0.82)

32 (70.6)

ALL INFORMATION, ILLUSTRATIONS, DIREC-

TIONS AND SPECIFICATIONS INCLUDED IN THIS

PUBLICATION ARE BASED ON THE LATEST PROD-

UCT INFORMATION AVAILABLE AT THE TIME OF

APPROVAL FOR PRINTING. HONDA MOTOR CO.,

LTD. RESERVES THE RIGHT TO MARE CHANGES

AT ANY TIME WITHOUT NOTICE AND WITHOUT

INCURRING ANY OBLIGATION WHATEVER.

NO PART OF THIS PUBLICATION MAY BE RE-

PRODUCED WITHOUT WRITTEN PERMISSION.

ILLUSTRATIONS AND SPECIFICATIONS IN OWN-

ER’S MANUAL IS REPRESENTATIVE TYPE.

HONDA

HONDA MOTOR CO., LTD: TOKYO, JAPAN

@@A 10008008

3189120

PRINTED IN JAPAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GV400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info