Bedienungsanleitung Honda Honda Engines GX100 Rammer (Seite 9 von 48) (Englisch)

13091

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

−

−−

−

ENGLISH

Cleaning SPARK PLUG

Recommended Spark Plugs:

SPARK PLUG WRENCH

SEALING

WASHER

AIR CLEANER CASE

SCREWS

AIR CLEANER COVER

0.60 0.70 mm

(0.024 0.028 in)

SIDE ELECTRODE

PAPER AIR FILTER ELEMENT

SPARK PLUG CAP

FOAM AIR FILTER ELEMENT

(applicable types)

Inspect the spark plug.

Replace it if damaged or

badly fouled, if the sealing

washer is in poor condition,

or if the electrode is worn.

Measure the spark plug

electrode gap with a wire-

type feeler gauge. Correct the

gap, if necessary, by carefully

bending the side electrode.

The gap should be:

Install the spark plug carefully,

by hand, to avoid cross-

threading.

When installing a new spark plug, tighten 1/2 turn after the spark

plug seats to compress the washer.

When reinstalling the original spark plug, tighten 1/8 1/4 turn

after the spark plug seats to compress the washer.

A loose spark plug can overheat and damage the engine.

Overtightening the spark plug can damage the threads in the

cylinder head.

Attach the spark plug cap to the spark plug.

Remove two screws from the air cleaner cover, and remove the

cover.

Remove the foam air filter element from the cover.

Remove the paper air filter element from the air cleaner case.

Clean the air filter elements if they are to be reused.

Wipe dirt from the inside of the air cleaner case and cover using

a moist rag. Be careful to prevent dirt from entering the air duct

that leads to the carburetor.

Place the foam air filter element to the air cleaner cover, then

reinstall the paper air filter element and cover to the air cleaner

case.

Install the air cleaner cover, and tighten the two screws securely.

Inspect both air filter elements, and replace them if they are

damaged. Always replace the paper air filter element at the

scheduled interval (see page ).

CR5HSB (NGK)

U16FSR-UB (DENSO)

The recommended spark plug is the correct heat range for normal

engine operating temperatures.

An incorrect spark plug can cause engine damage.

For good performance, the spark plug must be properly gapped

and free of deposits.

Disconnect the spark plug cap, and remove any dirt from around

the spark plug area.

Remove the spark plug with a 5/8-inch spark plug wrench.

After the spark plug is seated, tighten with a 5/8-inch spark plug

wrench to compress the sealing washer.

Paper air filter element: Tap the paper air filter element several

times on a hard surface to remove dirt, or blow compressed air

[not exceeding 207 kPa (2.1 kgf/cm

, 30 psi)] through the filter

element from the air cleaner case side. Never try to brush off

dirt; brushing will force dirt into the fibers. Replace the paper air

filter element if it is excessively dirty.

Foam air filter element: Clean in warm soapy water, rinse, and

allow to dry thoroughly. Or clean in nonflammable solvent and

allow to dry. Do not put oil on the foam air filter element.

0.60 0.70 mm (0.024 0.028 in)

06/01/24 10:13:54 32Z4E800_009

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GX100 Rammer Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GX100 Rammer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info