Bedienungsanleitung Honda Honda Engines GX200 (Seite 3 von 60) (Englisch)

13107

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

BEFORE OPERATION CHECKSFEATURES

IS YOUR ENGINE READY TO GO?

Check the General Condition of the Engine

Check the Engine

OIL ALERT SYSTEM (applicable types)

CIRCUIT PROTECTOR (applicable types)

ENGLISH

CIRCUIT

PROTECTOR

OFF

For your safety, and to maximize the service life of your

equipment, it is very important to take a few moments before you

operate the engine to check its condition. Be sure to take care of

any problem you find, or have your servicing dealer correct it,

before you operate the engine.

Improperly maintaining this engine, or failure to

correct a problem before operation, can cause a

malfunction in which you can be seriously hurt or

killed.

Always perform a preoperation inspection before

each operation, and correct any problem.

The Oil Alert

system is designed to prevent engine damage

caused by an insufficient amount of oil in the crankcase. Before

the oil level in the crankcase can fall below a safe limit, the Oil

Alert

system will automatically stop the engine (the engine

switch will remain in the ON position).

If the engine stops and will not restart, check the engine oil level

(see page ) before troubleshooting in other areas.

Before beginning your preoperation checks, be sure the engine is

level and the engine switch is in the OFF position.

Always check the following items before you start the engine:

Look around and underneath the engine for signs of oil or

gasoline leaks.

Remove any excessive dirt or debris, especially around the

muffler and recoil starter.

Look for signs of damage.

Check that all shields and covers are in place, and all nuts, bolts,

and screws are tightened.

Check the fuel level (see page ). Starting with a full tank will

help to eliminate or reduce operating interruptions for refueling.

Check the engine oil level (see page ). Running the engine

with a low oil level can cause engine damage.

The Oil Alert

system (applicable types) will automatically stop

the engine before the oil level falls below safe limits. However,

to avoid the inconvenience of an unexpected shutdown, always

check the engine oil level before startup.

The green indicator inside the

circuit protector will pop out to

show that the circuit protector has

switched off. If this occurs,

determine the cause of the

problem, and correct it before

resetting the circuit protector.

Push the circuit protector button

to reset.

Check the reduction case oil level on applicable types (see page

). Oil is essential to reduction case operation and long life.

Check the air filter element (see page ). A dirty air filter

element will restrict air flow to the carburetor, reducing engine

performance.

Check the equipment powered by this engine.

Review the instructions provided with the equipment powered

by this engine for any precautions and procedures that should

be followed before engine startup.

The circuit protector protects the

battery charging circuit. A short

circuit, or a battery connected

with reverse polarity, will trip the

circuit protector.

05/06/17 17:22:36 32Z4F601_003

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GX200 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GX200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info