Bedienungsanleitung Honda Honda Engines GX35 (Seite 15 von 60) (Englisch)

13123

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Storage PrecautionsDraining the Fuel Tank and Carburetor

Engine Oil

Removal from Storage

TRANSPORTING

ENGLISH

ENGINE OIL FILLER CAP

PRIMING BULB

FUEL FILLER NECK

FUEL RETURN TUBE

If your engine will be stored with gasoline in the fuel tank and

carburetor, it is important to reduce the hazard of gasoline vapor

ignition. Select a well-ventilated storage area away from any

appliance that operates with a flame, such as a furnace, water

heater, or clothes dryer. Also avoid any area with a spark-

producing electric motor, or where power tools are operated.

If possible, avoid storage areas with high humidity, because that

promotes rust and corrosion.

Keep the engine level in storage. Tilting can cause fuel or oil

leakage.

With the engine and exhaust system cool, cover the engine to

keep out dust. A hot engine and exhaust system can ignite or melt

some materials. Do not use sheet plastic as a dust cover.

A nonporous cover will trap moisture around the engine,

promoting rust and corrosion.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when handling

fuel.

Stop engine and keep heat, sparks, and flame away.

Wipe up spills immediately.

Handle fuel only outdoors.

Make sure the engine oil filler cap is tightened securely.

Remove the fuel filler cap and drain the fuel into an approved

gasoline container by tipping the engine toward the fuel filler

neck.

Press the priming bulb several times until there is no more fuel

in the fuel return tube.

Tip the engine toward the fuel filler neck again to drain the fuel.

After all fuel has drained, reinstall the fuel filler cap securely.

Change the engine oil (see page ).

Loosen the 5 mm hex bolt, then remove the top cover (see page

Remove the spark plug (see page ).

Apply a couple of drops of clean engine oil into the cylinder.

Install the top cover temporarily.

Pull the starter grip several times to distribute the oil in the

cylinder.

Remove the top cover, then reinstall the spark plug.

Install the top cover, and tighten the 5 mm hex bolt securely (see

page ).

Pull the starter grip slowly until resistance is felt.

Check your engine as described in the

BEFORE OPERATION

CHECKS

section of this manual (see page ).

If the fuel was drained during storage preparation, fill the tank with

fresh gasoline. If you keep a container of gasoline for refueling, be

sure it contains only fresh gasoline. Gasoline oxidizes and

deteriorates over time, causing hard starting.

If the cylinder was coated with oil during storage preparation, the

engine will smoke briefly at startup. This is normal.

If the engine has been running, allow it to cool for at least 15

minutes before loading the engine-powered equipment on the

transport vehicle. A hot engine and exhaust system can burn you

and can ignite some materials.

05/12/16 15:02:29 32Z6J600_015

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GX35 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GX35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info