Bedienungsanleitung Honda Honda Engines GXV50 (Seite 11 von 48) (Englisch, Französisch, Spanisch)

13157

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

−−

Storage Precautions

Engine Oil

Draining the Fuel Tank and Carburetor

Engine Cylinder

Removal from Storage

TRANSPORTING

ENGLISH

DRAIN BOLT

GASKET

CARBURETOR

Aligntheribontheflywheelwith

the notch on the fan cover.

If your engine will be stored with gasoline in the fuel tank and

carburetor, it is important to reduce the hazard of gasoline vapor

ignition. Select a well-ventilated storage area away from any

appliance that operates with a flame, such as a furnace, water

heater, or clothes dryer. Also avoid any area with a spark-

producing electric motor, or where power tools are operated.

If possible, avoid storage areas with high humidity, because that

promotes rust and corrosion.

Keep the engine level in storage. Tilting can cause fuel or oil

leakage.

With the engine and exhaust system cool, cover the engine to

keep out dust. A hot engine and exhaust system can ignite or melt

some materials. Do not use sheet plastic as a dust cover.

A nonporous cover will trap moisture around the engine,

promoting rust and corrosion.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when handling

fuel.

Stop engine and keep heat, sparks, and flame away.

Wipe up spills immediately.

Place an approved gasoline container below the carburetor, and

use a funnel to avoid spilling fuel.

Handle fuel only outdoors.

Reinstall the spark plug.

Pour a tablespoon 5 10 cm

(5 10 cc) of clean engine oil into

the cylinder.

Remove the spark plug (see page ).

Change the engine oil (see page ).

After all fuel has drained into the container, reinstall the

carburetor drain bolt and gasket. Tighten the carburetor drain

bolt securely.

Pull the starter grip slowly until resistance is felt and the notch

on the starter pulley aligns with the hole at the top of the recoil

starter cover. This will close the valves so moisture cannot enter

the engine cylinder. Return the starter grip gently.

Check your engine as described in the

BEFORE OPERATION

CHECKS

section of this manual (see page ).

If the fuel was drained during storage preparation, fill the tank with

fresh gasoline. If you keep a container of gasoline for refueling, be

sure it contains only fresh gasoline. Gasoline oxidizes and

deteriorates over time, causing hard starting.

If the cylinder was coated with oil during storage preparation, the

engine will smoke briefly at startup. This is normal.

If the engine has been running, allow it to cool for at least 15

minutes before loading the engine-powered equipment on the

transport vehicle. A hot engine and exhaust system can burn you

and can ignite some materials.

Keep the engine level when transporting to reduce the possibility

of fuel leakage. Turn the fuel valve lever to the OFF position. Close

the fuel tank vent by turning vent knob clockwise.

Remove the carburetor drain bolt and gasket, then turn the fuel

valve lever to the ON position.

Pull the starter grip several times to distribute the oil in the

cylinder.

06/11/28 13:57:23 32Z4D602_011

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GXV50 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GXV50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info