Bedienungsanleitung Honda HRX537 HYEA (Seite 8 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

580898

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

Installation

1. Raise the discharge

guard [1], and use

the grass bag handle

[3] to hook the grass

bag [2] onto the

mower deck as

shown.

2. Release the

discharge guard to

secure the grass

bag.

Removal

1. Raise the discharge

guard, grasp the

grass bag handle,

and remove the

grass bag.

2. Release the discharge guard.

3. When the grass bag is clear of the discharge guard, you can lift it

through the handlebar opening, or you can remove it to the rear of

the mower below the handlebar.

Cutting Height

Check the mower deck cutting

height settings, and be sure that

all four adjustment levers [1] are

set to the same cutting height

position.

To adjust cutting height, pull

each adjustment lever [1]

toward the wheel, and move it

into another notch.

If you are not sure what cutting

height to select, start with a

high setting and check the

appearance of the lawn after

mowing a small area. Then

readjust cutting height if

necessary.

Rear Shield

During normal use the rear

shield [1] is subject to

deterioration and wear.

Remove the grass bag and

raise the discharge guard [2] to

check the rear shield for cracks

or tears. If the rear shield is

excessively worn, have it

replaced by your authorized

Honda servicing dealer.

Clip Director

Clip Director Knob Adjustment

Adjust the Clip Director knob [1] in any one of the ten positions to

achieve the desired mowing results.

To adjust the Clip Director knob, pull the knob downward and towards

the rear of the mower. The knob adjusts a sliding door [2] from the

fully open BAG position to the fully closed MULCH position (see the

following page).

If a high resistance is noticed when moving the Clip Director knob

from side-to-side, excessive grass may have built up on top of the

sliding door.

Some grass accumulation in the discharge opening is normal when

the Clip Director is fully closed. To remove this grass, close the

discharge guard, fully open the Clip Director, start the engine, and

engage the blade control lever several times.

Important Safety Precaution

Always turn the engine off and disconnect the spark plug cap before

lifting the discharge guard to view or clean around the sliding door.

This will prevent contact with the rotating blades and prevent objects

from being thrown into the discharge area.

Sliding Door Position

The sliding door [2] can be positioned to produce different mowing

results. If the preferred sliding door position is unknown, install a

grass bag and begin mowing with the Clip Director knob [1] all the

way to the BAG position. Check the appearance of the lawn. As the

knob is moved towards the MULCH position, more grass will be

[3]

[1]

[2]

[1]

19 mm

32 mm

46 mm

62 mm

75 mm

88 mm

101 mm

[1]

[2]

[1]

[2] (fully closed)

DISCHARGE

GUARD

00X39VH7 Y210.book Page 8 Thursday, May 30, 2013 2:17 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda HRX537 HYEA Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda HRX537 HYEA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info