Bedienungsanleitung Honda HRX537 HYEA (Seite 15 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

580898

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

3. Inspect the spark plug. Replace it

if the electrodes are worn or if the

insulator is cracked or chipped.

Clean the spark plug with a wire

brush if you are going to reuse it.

4. Measure the spark plug electrode

gap with a suitable gauge. The

gap should be 0.7 ~ 0.8 mm.

Correct the gap, if necessary, by

carefully bending the side

electrode.

5. Install the spark plug carefully, by

hand, to avoid cross-threading.

6. After the spark plug seats, tighten with a spark plug wrench to

compress the washer.

If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the

spark plug seats.

If installing a new spark plug, tighten 1/2 turn after the spark plug

seats to compress the washer [4].

NOTICE

A loose spark plug can overheat and damage the engine.

Overtightening the spark plug can damage the threads in the

cylinder head.

7. Install the spark plug cap on the spark plug.

Spark Arrester Service

In Europe and other countries where machinery directive 2006/42/EC

is enforced, this cleaning should be done by your servicing dealer.

The spark arrester must be serviced every 100 hours to keep it

functioning as designed.

1. Allow the engine to cool, and then remove the three bolts [1] from

the muffler shield [2] using a 10 mm socket wrench.

2. Remove the muffler shield [2].

3. Remove the screw [4].

4. Remove the spark arrester [3] from the muffler [5].

5. Check for carbon deposits on the spark arrester and the exhaust

port. Brush carbon deposits away. Be careful to avoid damaging

the spark arrester screen.

6. Install the spark arrester in the muffler.

7. Install the muffler components on the engine, and tighten the three

bolts securely.

CONTROL CABLE ADJUSTMENTS

Blade Control Cable

Measure free play at the top of the blade control lever [1], while

holding the button down. Free play should be 10 ~ 15 mm. If

adjustment is necessary:

1. Loosen the locknuts [2]

with a 10 mm wrench, and

move the adjuster [3] up

or down as required.

2. Tighten the locknuts and

recheck free play.

3. Start the engine outdoors,

and operate the blade

control lever.

If the blade does not start

or stop as it should, with

correct cable adjustment,

take the mower to an

authorized Honda dealer

for repair.

Drive Clutch Cable Adjustment

1. With the engine stopped,

position the control cable

bands [1] as shown.

2. Pull the shift lever all the

way back to the stop

position.

3. Start the engine and move

the throttle lever to the

FAST position.

4. Engage the drive clutch

lever [2] and confirm the

following:

a. Mower does not self-propel.

b. Mower begins to self-propel

or creeps very slowly forward

when the shift lever is moved

one notch forward.

If the mower does not operate as outlined above, go to

step 5. If the mower does operate as outlined above, adjustment is

not required.

0.7 ~ 0.8 mm

[4]

[5]

[4]

[2]

[3]

[1]

10 ~ 15 mm

[1]

[2]

[3]

[1]

280 mm

120 mm

[2]

00X39VH7 Y210.book Page 15 Thursday, May 30, 2013 2:17 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda HRX537 HYEA Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda HRX537 HYEA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info