Bedienungsanleitung Honda iGX240 (Seite 10 von 60) (Englisch, Französisch, Spanisch)

566437

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

AIR CLEANER

Inspection (standard types)

Cleaning (standard types)

Inspection (low profile types)

Cleaning (low profile types)

LOW PROFILE TYPES

PAPER FILTER

ELEMENT

NUT

AIR CLEANER

COVER

WING NUT

FOAM FILTER

ELEMENT

SILENCER

NOSE

GASKET

Dry

Soak Squeeze Oil

Squeeze

AIR CLEANER CASE

AIR CLEANER COVER

CLIP

FOAM FILTER

ELEMENT

A dirty air cleaner will restrict air flow to the carburetor, reducing

engine performance. If you operate the engine in very dusty areas,

clean or replace the air filter more often than specified in the

MAINTENANCE SCHEDULE.

Operating the engine without an air filter, or with a damaged air

filter, will allow dirt to enter the engine, causing rapid engine wear.

This type of damage is not covered by the

Distributor’s Limited

Warranty.

Remove the air cleaner cover and inspect the filter elements.

Clean or replace dirty filter elements. Always replace damaged

filter elements.

Remove the nut from the air

cleaner cover, and remove

the cover.

Remove the wing nut from

the air filter, and remove the

filter.

Remove the foam filter from

the paper filter.

Inspect both air filter

elements, and replace them if

they are damaged. Always

replace the paper air filter

element at the scheduled

interval (see page ).

Clean the filter elements if they are to be reused.

Paper filter element: Tap the filter element several times on a hard

surface to remove dirt, or blow compressed air [not exceeding 207

kPa(2.1kgf/cm

, 30 psi)] through the filter element from the inside.

Never try to brush off dirt; brushing will force dirt into the fibers.

Foam filter element: Clean in warm soapy water, rinse, and allow

to dry thoroughly. Or clean in non-flammable solvent and allow to

dry. Dip the filter element in clean engine oil, and then squeeze out

all excess oil. The engine will smoke when started if too much oil

is left in the foam.

Wipe dirt from the inside of the air cleaner case and cover using

a moist rag. Be careful to prevent dirt from entering the air duct

that leads to the carburetor.

Place the foam filter element over the paper element, and

reinstall the assembled air filter. Be sure the gasket is in place

beneath the air filter. Tighten the air filter wing nut securely.

Install the air cleaner cover, and tighten the nut securely.

Remove the air cleaner cover and inspect the filter element.

Visually inspect the filter element. Clean the foam filter element.

Always replace damaged filter element.

Unsnap the air cleaner cover clips and remove the air cleaner

cover.

Remove the foam filter element from the air cleaner case.

Inspect the foam filter element, and replace it if it is damaged.

10/09/09 19:49:14 32Z8R800_010

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda iGX240 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda iGX240

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info