Bedienungsanleitung Honda iGX390 (Seite 14 von 60) (Englisch, Französisch, Spanisch)

566440

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

−−

ENGLISH

Engine Oil

Draining the Carburetor

(LOW PROFILE TYPES)

Storage Precautions

NOTCH

Align the notch on the pulley with

the center of the recoil starter cover.

GASKET

DRAIN BOLT

RECOIL STARTER COVER

FUEL VALVE LEVER

O-RING

SEDIMENT CUP

Change the engine oil (see page ).

Remove the spark plug (see page ).

Pour a teaspoon 5 10 cm

(5 10 cc) of clean engine oil into the

cylinder.

Pull the starter grip several times to distribute the oil in the

cylinder.

Reinstall the spark plug.

Pull the starter rope slowly until resistance is felt and the notch

on the starter pulley aligns with the center of the recoil starter

cover. This will close the valves so moisture cannot enter the

engine cylinder. Return the starter rope gently.

Gasoline is highly flammable and explosive, and you

can be burned or seriously injured when handling

fuel.

Stop the engine and keep heat, sparks, and flame

away.

Handle fuel only outdoors.

Wipe up spills immediately.

Unsnap the air cleaner cover clips, remove the air cleaner cover,

and remove the foam filter element (see page ).

Remove the air cleaner case and pull out the breather tube, then

remove the air cleaner base (see page ).

Move the fuel valve lever to the OFF position.

Place an approved gasoline container below the carburetor, and

use a funnel to avoid spilling fuel.

Remove the carburetor drain bolt and gasket. Remove the

sediment cup and O-ring, then move the fuel valve lever to the

ON position.

After all the fuel has drained into the container, reinstall the

drain bolt, gasket, sediment cup and O-ring. Tighten the drain

bolt and sediment cup securely.

Install the air cleaner base, breather tube, air cleaner case, foam

filter element, and air cleaner cover in the reverse order of

removal.

If your engine will be stored with gasoline in the fuel tank and

carburetor, it is important to reduce the hazard of gasoline vapor

ignition. Select a well ventilated storage area away from any

appliance that operates with a flame, such as a furnace, water

heater, or clothes dryer. Also avoid any area with a spark-

producing electric motor, or where power tools are operated.

If possible, avoid storage areas with high humidity, because that

promotes rust and corrosion.

Keep the engine level in storage. Tilting can cause fuel or oil

leakage.

With the engine and exhaust system cool, cover the engine to

keep out dust. A hot engine and exhaust system can ignite or melt

some materials. Do not use sheet plastic as a dust cover.

A nonporous cover will trap moisture around the engine,

promoting rust and corrosion.

If equipped with a battery for electric starter types, recharge the

battery once a month while the engine is in storage.

This will help to extend the service life of the battery.

10/09/09 19:50:37 32Z8R800_014

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda iGX390 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda iGX390

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info