Bedienungsanleitung Honda Miimo HRM3000 (Seite 40 von 112) (Englisch)

720161

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Setting the lawnmower operation

Auto mode

You can set up the advanced auto mode settings as follows:

Point 1

Point 2

Point 3

Point 4

Point 5

Setting the value to reach other areas through the

narrow passage

The lawnmower can reach other areas through narrow

passages with the following settings:

- Congure the minimum value (“0”) of Narrow passage

in the Advanced setting. The lawnmower closely follows

the boundary wire. This is effective for 5 or more narrow

pathways in the garden.

- Congure the value of the narrow passage distance from

the docking station. When passing the congured narrow

passage, the lawnmower closely follows the boundary

wire. This is effective for 4 or fewer narrow pathways in the

garden.

L Width settings in [1.Mowing start points] (M page 40)

L [6.Narrow passage] (M page 44)

NOTE:

- [6.Narrow passage] setting is for going toward the starting

point. If you want to congure the setting for returning to

the docking station, you need to set it in the Homing setup.

For details, see “Homing setup” (M page 48).

Setting the overlap

distance on the

boundary wire

Set the distance that the

lawnmower can cross the

boundary wire.

L [3.Wire Overlap]

(M page 41)

NOTE:

- To have the lawnmower

smoothly turn from

the boundary wire, the

recommended value of

the Wire overlap is 20 cm.

Setting the distance to the start point

Until the lawnmower reaches a set starting point

in an area, it will run without mowing.

L Distance settings in [1.Mowing start points]

(M page 40)

- Sets the distance from the docking station to

start cutting.

Setting the starting

direction from the

docking station

Set whether the

lawnmower should

travel clockwise or

anticlockwise along the

boundary wire to reach

a set starting point.

L (Clockwise) or

(Anticlockwise)

in [1.Mowing start

point]

(M page 40)

Setting the angle to turn from the boundary wire

When leaving the boundary wire, set the angle to turn

from the boundary wire.

L Angle settings in [1.Mowing start points] (M page 40)

- Set the angle of departure for when the lawnmower

arrives at the position specied by the angle of

[1.Mowing start point].

Setting the operation ratio of each area

operation

Set an area operation ratio if you want to mow

more frequently from a certain start point.

For example, if you set the ratio for “Point 1” to

30%, the lawnmower will start mowing 3 times

out of 10 from “Point 1” and 7 times out of 10

from other start points.

L Percentage settings in [1.Mowing start points]

(M page 40)

NOTE:

- You can congure 5 start points.

NOTE:

- If you want to operate the lawnmower with [Auto mode], see “Operating the lawnmower in Auto mode.”

(M page 69).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Miimo HRM3000 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Miimo HRM3000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info