Bedienungsanleitung Honda Pilot 2016 (Seite 14 von 89) (Englisch)

624604

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

20 | | 21

SAFETYSAFETY

TABLE OF CONTENTS

INDEX

VISUAL INDEX

VOICE COMMAND

INDEX

SAFETY

INFORMATION

CUSTOMER

INFORMATION

INSTRUMENT PANEL

SPECIFICATIONS

VEHICLE

CONTROLS

MAINTENANCE

AUDIO AND

CONNECTIVITY

HANDLING THE

UNEXPECTED

BLUETOOTH®

HANDSFREELINK®

DRIVING

HONDALINK®

NAVIGATION

Installing a Child Seat with a Lap/Shoulder Seat Belt

1. Place the child seat on the vehicle seat.

2. Route the seat belt through the child seat

according to the seat manufacturer’s

instructions, and insert the latch plate into the

buckle. Insert the latch plate fully until it clicks.

3. Slowly pull the shoulder part of the belt all the

way out until it stops. This activates the lockable

retractor.

4. Let the seat belt completely wind up into the

retractor, then try to pull it out to make sure the

retractor is locked. If you are able to pull the

shoulder belt out, the lockable retractor is not

activated. Pull the seat belt all the way out, and

repeat steps 3 – 4.

5. Grab the shoulder part of the seat belt near the

buckle, and pull up to remove any slack from

the lap part of the belt. When doing this, place

your weight on the child seat and push it into the

vehicle seat.

6. Make sure the child seat is ﬁrmly secured by

rocking it forward and back and side to side; little

movement should be felt.

7. Make sure any unused seat belt that a child

can reach is buckled, the lockable retractor

is activated, and the belt is fully retracted and

locked.

To deactivate a lockable retractor, release the buckle and allow the seat belt to

wind up all the way.

Adding Security with a Tether

A tether anchorage point is provided behind each second- and third-row seating

position. If you have a child restraint system that comes with a tether but can be

installed with a seat belt, the tether may be used for additional security.

Using a second-row anchor

1. For outer positions: Raise the outer head

restraint to its highest position, then route the

tether strap between the head restraint legs, and

secure the tether strap hook onto the anchor.

Make sure the strap is not twisted.

For the center position: Lower the center head

restraint to its lowest position, then route the

tether strap over the top of the head restraint,

and secure the tether strap hook onto the anchor.

Make sure the strap is not twisted.

2. Tighten the tether strap as instructed by the child

seat manufacturer.

Using a third-row anchor

1. Route the tether strap hook between the head

restraint legs, and secure the tether strap hook

onto the anchor. Make sure the strap is not

twisted.

2. Secure the tether strap hook onto the anchor.

3. Tighten the tether strap as instructed by the child

seat manufacturer.

Second-row bench seat

Tether anchorage points

Second-row captain seat

Tether anchorage points

Second-row bench seat

Tether strap hook

Anchor

Third row seat

Tether anchorage points

Second-row captain seat

Anchor

Tether strap hook

Third row seat

Anchor

Tether strap hook

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Pilot 2016 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info