Bedienungsanleitung Honda UMK431E (Seite 9 von 58) (Deutsch, Englisch, Französisch)

478014

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

SAFETY INSTRUCTIONS

B4.Replace faulty exhaust mufflers.

B5.Each timethe machine isused, beforestarting, perform a generalinspection and check,in particular,all attachments, cutting

assemblies,deflectors and mounting bolts tomake sure that theyare not worn, damagedor loose.Always check that thegas

throttle trigger and the Stop button operate correctly.

B6.Check that the handles andharnessattachmentpoint are correctly positioned andthatthemachine is properly balanced. The

correct positions and adjustments are specified in the section on “Preliminary preparation and checks” in this manual.

B7.Adjust the idle speed so that the cutting attachment stops turning when the throttle control is released.

B8.Install the blade cover on the blade type cutter during removal and installation operations.

- Turn the engine switch to the Stop position and remove the spark plug cap.

- Wear gloves during this operation.

OPERATION

C1.Do not run the engine in a confined space where toxic carbon monoxide fumes may accumulate.

C2.Work by daylight only.

C3.As far as possible, avoid using the machine on wet ground.

C4.When operating the machine, ensure compliance with the safety clearance of the nylon line cutting head with respect to the

harness attachment point.

C5.Walk whenyouusethemachine,neverrun,andstay ina stableposition.Bewareofobstaclessuchas stonesand treestumps

which could trip you.

C6.Tread carefully on slopes. When working on slopes, always proceed crosswise: never straight up and down.

C7.Do not use the machine onslopes that are too steep. It is the operator’s responsibility to assess the potential hazards of the

terrainandtotakeeverynecessaryprecautionforhisorherownsafety.Thisisespeciallyimportantwhenworkingonslopesor

rough, slippery or loose ground.

C8.Never modify the engine settings in such a way that it runs at excessive speeds.

C9.Before starting the engine, make sure there is no-one within 15 metres of the machine, that the cutting attachment is not

touching the ground and that the machine is in a stable position.

C10.Take care when starting the engine. Comply with the safety instructions and stay clear of the cutting attachment.

C11.The engine must be stopped and the spark plug cap removed in the following cases:

- Before performing any servicing action on the cutting system.

- Before cleaning, checking, adjusting or repairing the brushcutter.

- The only adjustments to be carried out with the engine running are carburettor and idle speed adjustments.

- During this operation, make sure the cutting attachment does not strike any object and that the machine is in a stable

position.

- Ifthecuttingattachment strikesanobject,inspectthe cuttingsystemandthetransmission shafttomakesurethey havenot

been damaged. Make any necessary repairs before resuming work with the machine.

- If the brushcutter starts vibrating abnormally, look for the cause of the vibrations immediately and take the necessary

corrective action.

C12.Stop the engine in the following cases:

- Whenever the brushcutter is left unattended.

- Before refilling the fuel tank.

- When moving the machine from one area to another.

MAINTENANCE AND STORAGE

D1.Keep all nuts and bolts securely tightened to ensure safe operation. Regular maintenance is required to ensure safety and

optimal performance.

D2.Do not use the machine with damaged or worn parts. Parts must be replaced, not repaired. Use genuine Honda parts. The

cuttingattachments must alwaysbemarkedwith the manufacturer’sbrand,the reference and themaximumoperating speed.

Parts of inferior quality may damage the machine and compromise operator safety.

D3.Wear heavy gloves when removing and installing the cutting device.

D4.Neverstorethebrushcutterwithfuelinthefueltankinaroomwherefuelvapourcouldbeignitedbyaflame,asparkorasource

of intense heat.

D5.Store in a clean dry room, out of the reach of children.

D6.Let the engine cool down before putting away the machine in any room.

D7.To reduce fire hazards, remove leaves, grass cuttings and excessoil from the brushcutter, particularly from thecooling fins,

the exhaust system and the fuel storage area.

D8.When themachineisstoredor carried,thecuttingblademustalwaysbe coveredbyitstransportguard toavoid anyaccidental

injury.

D9.If the fuel tank has to be drained, this operation must be performed outdoors when the engine is cold.

D10.To protectthe environment, do notdispose of old engineoil orfuel by pouring itdown the drain, in thegutter or on theground.

Your local service station can have oil and fuel safely recycled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda UMK431E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda UMK431E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info