Bedienungsanleitung Honda UMK435E (Seite 4 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

478015

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

4 EN

FITTING

GRIPS AND HANDLES

The bike type handle [1] (U type)

or the loop handle [2] (L types)

must be installed on the

transmission tube [3].

CAUTION:

• U types: Position the handle

between the two arrows [4].

Fitting is to be performed using

the tools in the kit supplied with

the appliance.

ATTACHMENT

PROTECTORS

Your brush cutter is supplied with

a guard.

Install the guard on the machine

with the four screws [8] and the

spacer [7] supplied with the Torx

wrench.

UTILIZATION WITH NYLON

LINE CUTTING HEAD

Fit the two sections [10] and [9]

and clamp them into place as

shown in the diagram. Screw the

3 screws and the washers by

using the torx wrench.

UTILIZATION WITH BLADE

Do not fit the lower section [10].

Never use the grass/weed trimmer without its debris shield.

Stones or other foreign objects thrown outward by the

wheeling cutting attachment (nylon-line, cutting head or

cutting blade) or contact with the wheeling cutting attachment

could cause personal injury or property damage.

ASSEMBLING THE CUTTING

SYSTEM

CAUTION:

• Pay special attention when

fitting the spacer [13]. The

concave side must face the

transmission [15].

NYLON LINE CUTTING HEAD

With the spacer [13] already fitted

on the transmission shaft, screw

on the nylon line cuttinghead. It is

tightened by turning

counterclockwise.

Use the hexagonal wrench [14] to immobilize the transmission so

that the nylon line cutting head is properly tightened.

3 - TOOTH BLADE

Place the grass-cutting disc [16]

between the spacers [13]

and [17] so that the grooves on

the spacers fit perfectly onto the

shaft.

Install the stabilizer [18]. Block

the rotation of the shaft with the

hexagonal wrench [14]. Securely

tighten the locknut [19] in the

counterclockwise direction with

the appropriate wrench.

FITTING AND

ADJUSTING THE

HARNESS

For operator safety and

comfort, it is important to

adjust the harness straps so

they can be worn comfortably

and so that the machine is

properly balanced in the

working position.

Machines are supplied with a

double harness [22].

Put on the harness and fasten it

with the quick fastener [23].

Adjust the straps with the

buckles [24] so that the machine

hangs at hip height.

PRELIMINARY PREPARATION

AND CHECKS

BALANCING THE MACHINE

Attach the brush cutter as

illustrated [1].

Once the machine is in place, it is

essential to check that it is

correctly balanced. This check

must be performed with the

cutting attachment fitted on the

appliance and with the fuel tank

half-full.

Adjust the length of the harness

so that the cutting attachment is

parallel to, and in contact with, the

ground.

[5] Spark plug wrench / Torx wrench [6] Hexagonal wrench

SAFETY

C11

[2]

[3]

[1]

[3]

[4]

[7]

[8]

[10]

[9]

[10]

[9]

SAFETY

C11 D3

[14]

[15]

[13]

[14]

[16]

[17]

[18]

[19]

[13]

[24]

[23]

[22]

[24]

[1]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda UMK435E Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda UMK435E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info